ITT HT 3196 i-FRAME Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 148

background image

Pump operation precautions

General considerations

CAUTION:

• Vary the capacity with the regulating valve in the discharge line. Never throttle the flow from the

suction side since this can result in decreased performance, unexpected heat generation, and
equipment damage.

• Do not overload the driver. Driver overload can result in unexpected heat generation and equipment

damage. The driver can overload in these circumstances:
• The specific gravity of the pumped fluid is greater than expected.
• The pumped fluid exceeds the rated flow rate.

• Make sure to operate the pump at or near the rated conditions. Failure to do so can result in pump

damage from cavitation or recirculation.

Operation at reduced capacity

WARNING:
Never operate any pumping system with a blocked suction and discharge. Operation, even for a brief
period under these conditions, can cause confined pumped fluid to overheat, which results in a violent
explosion. You must take all necessary measures to avoid this condition.

CAUTION:

• Avoid excessive vibration levels. Excessive vibration levels can damage the bearings, stuffing box or

seal chamber, and the mechanical seal, which can result in decreased performance.

• Avoid increased radial load. Failure to do so can cause stress on the shaft and bearings.
• Avoid heat build-up. Failure to do so can cause rotating parts to score or seize.
• Avoid cavitation. Failure to do so can cause damage to the internal surfaces of the pump.

Operation under freezing conditions

NOTICE:
Do not expose an idle pump to freezing conditions. Drain all liquid that is inside the pump and the cooling
coils. Failure to do so can cause liquid to freeze and damage the pump.

Shut down the pump

WARNING:
The pump can handle hazardous and toxic fluids. Identify the contents of the pump and observe proper
decontamination procedures in order to eliminate the possible exposure to any hazardous or toxic fluids.
Wear the proper personal protective equipment. Potential hazards include, but are not limited to, high
temperature, flammable, acidic, caustic, explosive, and other risks. You must handle and dispose of
pumped fluid in compliance with the applicable environmental regulations.

1. Slowly close the discharge valve.
2. Shut down and lock the driver to prevent accidental rotation.

Commissioning, Startup, Operation, and Shutdown

58

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
58
59
60
61
62
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Eccotemp Страницы: 56

Бренд: Quick Страницы: 16

Бренд: Larius Страницы: 56

WELCH DUOSEAL 1397C-46

Бренд: Gardner Denver Страницы: 28

Бренд: Jecod Страницы: 3

BEST ONE Series

Бренд: EBARA Страницы: 7

Бренд: Bock Water heaters Страницы: 62

Бренд: C.P.A. Страницы: 40

Бренд: Takagi Страницы: 56

Бренд: Greenlee Страницы: 34

Бренд: Laars Страницы: 36

1 EPBH 9.2-11 T-AVS

Бренд: EBARA Страницы: 16

Бренд: Waldbeck Страницы: 9

Бренд: Quincy Compressor Страницы: 42

Бренд: Klima hitze Страницы: 39

THERMOSIPHON 150/2.5

Бренд: SUN&HEAT Страницы: 38

VARION C-POWER 20.0

Бренд: elco Страницы: 44

Бренд: Tecnosystemi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды