ITT HT 3196 i-FRAME Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 148

background image

Assemble the rotating element and the bearing frame ( XLT-i and i17 )

CAUTION:

• Wear insulated gloves when you use a bearing heater. Bearings get hot and can cause physical injury.
• Use care when you handle the shaft because it can be heavy. Failure to do so could result in personal

injury.

NOTICE: Make sure that the pipe threads are clean, and that you apply thread sealant to the plugs and
fittings. Failure to do so may result in equipment damage or decreased performance.

NOTICE: Use an induction heater that heats as well as demagnetizes the bearings when you install
bearings. Failure to do so may result in decreased performance.

1. Prepare the bearing frame (228) as follows (see the illustration):

a) Install the oil-fill plug (113A).
b) Install the oil-drain plug (408A).
c) Install the sight glass (319).
d) Install the sight oiler plug (408J).
e) Install the plug for the oil-cooler inlet (408L).
f) Install the plug for the oil-cooler outlet (408M).
g) Install four oil-mist connection plugs (408H).

Or: Install two grease fittings (193) and two grease-relief plugs (113).

370F

241

408A

408L

319

228A

113A

408N

408M

2. Install the outboard bearings (112A) on the shaft (122).

The regreaseable bearing has a single shield. The outboard bearing is installed with the shield toward
the impeller.
a) Inspect the shaft (122) to ensure that it is clean, dimensionally correct, and is free of nicks and

burrs.

b) Lightly coat the bearing seating with a thin film of oil.
c) Remove the bearing (112) from its packaging.
d) Wipe the preservative from the bearing (112) bore and outer diameter.
e) Use an induction heater with a demagnetizing cycle to heat the bearing (112) to an inner ring

temperature of 230 °F (110 °C).

f) Position the bearing (112) on the shaft (122) against the shoulder and snug the locknut (136)

against the bearing until it is cool.
The locknut prevents the bearing from moving away from the shaft shoulder as it cools.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

99

«
...
99
100
101
102
103
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: OilGear Страницы: 28

Бренд: Lamborghini Caloreclima Страницы: 192

Бренд: Edwards Страницы: 16

NEVERCOLD 70600

Бренд: EASTMAN Страницы: 11

Бренд: Crivit Страницы: 23

Бренд: Annovi Reverberi Страницы: 16

SBC 1100 ADV PLUS FR

Бренд: Quick Страницы: 76

Бренд: hajdu Страницы: 132

Бренд: salmson Страницы: 195

Бренд: QED Страницы: 33

RIBILAND PRPVC1501V

Бренд: Ribimex Страницы: 35

Бренд: GASLAND chef Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды