ITT HT 3196 i-FRAME Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 148

background image

122

382

136

112A

Disassemble the bearing frame

1. Remove these plugs from the bearing frame (228A).

• oil-fill plug (113A)
• oil-drain plug (408A)
• sight-oiler plug (408J)
• four oil mist/grease connection plugs (408H)
• oil-cooler inlet and outlet plugs (408L and 408M) or oil cooler

2. For the MTi and LTi models, remove the bearing frame foot-to-frame bolts (370F) and the frame foot

(241).

319

408N

408A

241

370F

408N

408W

372T

113A

408W

408M

761B

Guidelines for i-ALERT

™

Condition Monitor disposal

Precautions

WARNING:

• Never heat the condition monitor to temperatures in excess of 300°F (149°C). Heating to these

temperatures could result in death or serious injury.

• Never dispose of the condition monitor in a fire. This could result in death or serious injury.

Guidelines

The battery contained in the condition monitor does not contain enough lithium to qualify as reactive
hazardous waste. Use these guidelines when disposing of the condition monitor.

• The condition monitor is safe for disposal in the normal municipal waste stream.
• Adhere to local laws when you dispose of the condition monitor.

Maintenance

82

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
82
83
84
85
86
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: A.O. Smith Страницы: 24

Бренд: GEAppliances Страницы: 72

Бренд: Qual Craft Страницы: 5

Бренд: Nakayama Страницы: 8

Бренд: Lamborghini Caloreclima Страницы: 192

Бренд: Zenit Страницы: 35

Бренд: IDEAL Страницы: 30

Feeder/Deliming System EV9797-20

Бренд: Everpure Страницы: 2

Бренд: Jandy Страницы: 24

Бренд: Graco Страницы: 20

EZH2O LZWS-LRPBM28K

Бренд: Elkay Страницы: 4

SMOOTHFLO Series

Бренд: Remco Страницы: 2

Бренд: AQUASYSTEM Страницы: 12

Serve Better CP-RP

Бренд: Server Страницы: 8

Бренд: Enertech Страницы: 40

Бренд: Wayne Страницы: 1

Бренд: Unitary products group Страницы: 16

Inverter Design

Бренд: Thermia Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды