ITT HT 3196 i-FRAME Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 148

background image

Make sure that the orientation of the bearing-clamp ring is correct.

4. Install outboard bearings (112A) on shaft (122).

The regreasable bearing has a single shield. Make sure that the bearing is installed with the shield away
from the impeller.
The duplex bearings are mounted back-to-back. Make sure that the orientation of the bearings are
correct.
a) Inspect the shaft (122) to ensure that it is clean, dimensionally correct, and is free of nicks and

burrs.

122

112

136

b) Lightly coat the bearing seating with a thin film of oil.
c) Remove the bearings (112) from their packaging.
d) Wipe the preservative from the bearing (112) bore and outer diameter.
e) Use an induction heater with a demagnetizing cycle to heat both bearings (112) to an inner ring

temperature of 230 °F (110 °C).

f) Place both bearings (112) on the shaft (122) with the large outer races together (back-to-back).
g) Position the bearings (112) on the shaft (122) against the shoulder and snug the locknut (136)

against the bearings until they are cool.
The locknut prevents the bearings from moving away from the shaft shoulder as they cool. Rotate
the outer bearing rings relative to each other as they are placed on the shaft to assure good
alignment.

h) Remove the bearing locknut (136) after the bearings (112) are cool.

5. Put the lockwasher (382) onto the shaft (122).
6. Thread the locknut (136) onto the shaft (122) and tighten it until it is snug.
7. Bend the tangs of the lockwasher into the slots of the locknut.
8. Coat the inner surfaces of the bearings with lubricant.
9. Put the inboard bearing (168) onto the shaft (122).

122

168A

248A

112A

136

382

253B

10. Install the bearing housing as follows (see the illustration):

a) Coat the outside of the outboard bearing (112A) with oil.
b) Coat the bore of the bearing housing (134) with oil.
c) Put the bearing housing (134) onto the shaft.

Do not use force.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

97

«
...
97
98
99
100
101
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Makita Страницы: 96

Бренд: Ace Страницы: 13

Бренд: Salamander Pumps Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 24

Бренд: WarmPool Страницы: 26

Бренд: Pentair Страницы: 36

GOULDS e-SVI Series

Бренд: Xylem Страницы: 40

Gyre 300 Series

Бренд: Maxspect Страницы: 164

Бренд: Bard Страницы: 24

Бренд: Idex Страницы: 40

Бренд: Accorroni Страницы: 29

Бренд: Panduit Страницы: 7

Бренд: Texas Equipment Страницы: 11

Kaysun Aquantia R-32 PRO

Бренд: Frigicoll Страницы: 44

Hydromatic SK60

Бренд: Pentair Pool Products Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды