ITT HT 3196 i-FRAME Скачать руководство пользователя страница 91

Страница: 91 / 148

Bearing-housing inspection

Checklist

• Inspect the bearing-housing (134) bore according to the bearing fits and tolerances table.
• Replace the bearing housing if the dimensions exceed acceptable values. Reference: see Bearings fits

and tolerances.

• Visually inspect the bearing housing for cracks and pits.

Checklist for specific models

This table shows bearing-housing checks that are required for specific models of pump.

Frame

Bearing-housing check

STi and MTi

Ensure that the snap-ring groove is not cracked.

LTi

Clear all grooves and holes.

XLT-i

Clean the gasket surface.

Inspection locations

The following images point to the areas to inspect on the bearing housing.

134

Figure 27: STi and MTi bearing housing

134

Figure 28: LTi bearing housing

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание HT 3196 i-FRAME





















































































































































Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды