ITT HT 3196 i-FRAME Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 148

background image

Maintenance

Maintenance schedule

Maintenance inspections

A maintenance schedule includes these types of inspections:

• Routine maintenance
• Routine inspections
• Three-month inspections
• Annual inspections

Shorten the inspection intervals appropriately if the pumped fluid is abrasive or corrosive or if the
environment is classified as potentially explosive.

Routine maintenance

Perform these tasks whenever you perform routine maintenance:

• Lubricate the bearings.
• Inspect the seal.

Routine inspections

Perform these tasks whenever you check the pump during routine inspections:

• Check the level and condition of the oil through the sight glass on the bearing frame.
• Check for unusual noise, vibration, and bearing temperatures.
• Check the pump and piping for leaks.
• Analyze the vibration.
• Inspect the discharge pressure.
• Inspect the temperature.
• Check the seal chamber and stuffing box for leaks.

• Ensure that there are no leaks from the mechanical seal.
• Adjust or replace the packing in the stuffing box if you notice excessive leaking.

Three-month inspections

Perform these tasks every three months:

• Check that the foundation and the hold-down bolts are tight.
• Check the packing if the pump has been left idle, and replace as required.
• Change the oil every three months (2000 operating hours) at minimum.

• Change the oil more often if there are adverse atmospheric or other conditions that might

contaminate or break down the oil.

• Check the shaft alignment, and realign as required.

Annual inspections

Perform these inspections one time each year:

• Check the pump capacity.
• Check the pump pressure.
• Check the pump power.

If the pump performance does not satisfy your process requirements, and the process requirements have
not changed, then perform these steps:
1. Disassemble the pump.
2. Inspect it.
3. Replace worn parts.

Maintenance

60

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
60
61
62
63
64
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Panasonic Страницы: 224

Бренд: abc Страницы: 8

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 86

Бренд: Danfoss Страницы: 28

Бренд: Vagner Pool Страницы: 35

Бренд: A.O. Smith Страницы: 4

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Бренд: vacuubrand Страницы: 80

Бренд: DAB Страницы: 41

Бренд: Mixtron Страницы: 44

Бренд: F.F. Group Страницы: 28

Бренд: RadonAway Страницы: 22

Бренд: FE PETRO Страницы: 16

PC 3010 NT VARIO o.C.

Бренд: vacuubrand Страницы: 92

Бренд: Giant Страницы: 12

Бренд: SAMES KREMLIN Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды