ITT HT 3196 i-FRAME Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 148

background image

113A

319

Oil lubricated

bearings

Correct

level

3. Replace the fill plug.

Lubricate the bearings with pure oil mist

Oil mist is an optional feature for this pump.

• To lubricate bearings with pure oil mist, follow the instructions provided by the manufacturer of the

oil-mist generator.
The inlet connections are on the top of the bearing frame.

Greased-for-life bearing lubrication

The bearing manufacturer fills greased-for-life bearings with grease and seals them at the factory. You do
not need to lubricate or seal these bearings. Refer to the Maintenance chapter for re-greasing and
maintenance procedures for these bearings.

Shaft-sealing options

In most cases, the manufacturer seals the shaft before shipping the pump. If your pump does not have a
sealed shaft, see the Shaft-seal maintenance section in the Maintenance chapter.
This model uses these types of shaft seals:

• Cartridge mechanical seal
• Conventional inside-component mechanical seal
• Conventional outside-component mechanical seal
• Packed-stuffing-box option

Mechanical seal options

Pumps are usually shipped with mechanical seals installed. If they are not, then refer to the mechanical seal
manufacturer's installation instructions.
These are the mechanical seal options for this pump:

• Cartridge mechanical seal
• Conventional inside component mechanical seal
• Conventional outside component mechanical seal

Connection of sealing liquid for mechanical seals

Seal lubrication is required

Seal faces must have liquid film between them for proper lubrication. Locate the taps using the illustrations
shipped with the seal.

Seal flushing methods

You can use these methods in order to flush or cool the seal:

Commissioning, Startup, Operation, and Shutdown

52

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
52
53
54
55
56
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Aquarea WH-MDF06E3E5 series

Бренд: Panasonic Страницы: 36

Бренд: Gardena Страницы: 17

Hydro-Guard HG-3

Бренд: Mueller Страницы: 7

Habitat PWF105-C

Бренд: Plantronics Страницы: 33

Бренд: Annovi Reverberi Страницы: 4

Бренд: Comet Страницы: 12

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Бренд: Pacific hydrostar Страницы: 36

Бренд: Calorex Страницы: 44

Бренд: American Water Heater Страницы: 24

Бренд: Oase Страницы: 31

Бренд: Oasis Страницы: 40

Бренд: YAMADA Страницы: 30

Бренд: Lutz Страницы: 16

Бренд: Emec Страницы: 44

Braukmann HS10S

Бренд: resideo Страницы: 38

Бренд: Simer Страницы: 16

Бренд: Enapter Страницы: 30

Бренд: VacuumChambers Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды