manualshive.com logo in svg

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

ITT HT 3196 i-FRAME - надежный и эффективный насос с высокой производительностью. Установите, работайте и поддерживайте его с помощью инструкции по монтажу, эксплуатации и техническому обслуживанию, которую можно бесплатно скачать с manualshive.com. Надежный помощник в вашем производстве.

Поделиться
Скачать
background image

Pre-assembly inspections...............................................................................................................................................83

Replacement guidelines...............................................................................................................................................83
Shaft and sleeve replacement guidelines...................................................................................................................85
Bearing-frame inspection............................................................................................................................................85
C-face adapter inspection...........................................................................................................................................86
Seal chamber and stuffing box cover inspection.....................................................................................................87
Bearings inspection......................................................................................................................................................88
Bearing-housing inspection........................................................................................................................................89
Bearing fits and tolerances..........................................................................................................................................90

Reassembly.......................................................................................................................................................................91

Assemble the rotating element and the bearing frame ( STi and MTi ) .............................................................91
Assemble the rotating element and the bearing frame ( STi and MTi with duplex bearings).........................93
Assemble the rotating element and the bearing frame ( LTi )..............................................................................96
Assemble the rotating element and the bearing frame ( XLT-i and i17 )............................................................99
Assemble the rotating element and the bearing frame ( XLT-i and i17 with duplex bearings).....................102
Assemble the frame...................................................................................................................................................105
INPRO labyrinth oil seal description.....................................................................................................................108
Assemble the INPRO labyrinth oil seal.................................................................................................................108
Assemble the C-face adapter....................................................................................................................................109
Shaft sealing................................................................................................................................................................109
Install the impeller.....................................................................................................................................................114
Attach the i-ALERT

™

 Condition Monitor to the pump....................................................................................116

Post-assembly checks................................................................................................................................................117
Reinstall the back pull-out assembly for the HT 3196.........................................................................................117
Assembly references..................................................................................................................................................117
Spare parts...................................................................................................................................................................119

Interchangeability drawings.........................................................................................................................................119

HT 3196 interchangeability......................................................................................................................................119

Lubrication conversion.................................................................................................................................................120

Frame lubrication conversion..................................................................................................................................120
Convert from greased-for-life or regreaseable to oil-lubricated bearings.........................................................121
Conversion from flood-oil to pure-oil mist...........................................................................................................122
Convert from flood oil to regreaseable..................................................................................................................122

Troubleshooting.............................................................................................................................................................123

Operation troubleshooting..........................................................................................................................................123
Alignment troubleshooting..........................................................................................................................................124
Assembly troubleshooting...........................................................................................................................................124
i-ALERT

™

 Condition Monitor troubleshooting.....................................................................................................125

Parts Listings and Cross-Sectional Drawings.......................................................................................................126

Parts list..........................................................................................................................................................................126

Certification: CE or CE ATEX..................................................................................................................................137

Certificates of  conformance........................................................................................................................................137

Other Relevant Documentation or Manuals.........................................................................................................143

For additional documentation.....................................................................................................................................143

Local ITT Contacts.......................................................................................................................................................144

Regional offices.............................................................................................................................................................144

Table of Contents

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

3

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Gardena 1732 Operating Instructions Manual preview
1732
Бренд: Gardena Страницы: 17
Haier MRV II AV08NMVERA Startup Manual preview
MRV II AV08NMVERA
Бренд: Haier Страницы: 40
Bacharach QV2 Instruction preview
QV2
Бренд: Bacharach Страницы: 12
Waterous CG Series Overhaul Instructions preview
CG Series
Бренд: Waterous Страницы: 10
Oasis Modular Series User Manual preview
Modular Series
Бренд: Oasis Страницы: 18
T.I.P. WP 500 Plus Operating Instructions Manual preview
WP 500 Plus
Бренд: T.I.P. Страницы: 24
Taco 00e Series Installation/Operation Instruction Manual preview
00e Series
Бренд: Taco Страницы: 56
Taco 1900e Series Instructions Manual preview
1900e Series
Бренд: Taco Страницы: 12
Zoeller Water Solutions 3098 Series Installation Instructions preview
Water Solutions 3098 Series
Бренд: Zoeller Страницы: 4
Zoeller Aquanot Spin 508 Technical Data Sheet preview
Aquanot Spin 508
Бренд: Zoeller Страницы: 2
Zoeller 1461-0006 Instructions Manual preview
1461-0006
Бренд: Zoeller Страницы: 11
Zip DEX Installation, Maintenance & User Instructions preview
DEX
Бренд: Zip Страницы: 18
AMICUS EPO.D1-4 Operating And Installation Instructions preview
EPO.D1-4
Бренд: AMICUS Страницы: 12
Becker BASIC VASF 2.120/1-0.AC115 Operating Instructions Manual preview
BASIC VASF 2.120/1-0.AC115
Бренд: Becker Страницы: 6
Noritz N-0751M Owner'S Manual preview
N-0751M
Бренд: Noritz Страницы: 26
Daikin Altherma FWXV10AATV3 Installation Manual preview
Altherma FWXV10AATV3
Бренд: Daikin Страницы: 20
A.O. Smith DSE-5 THRU DSE-120 Installation And Operaion Manual preview
DSE-5 THRU DSE-120
Бренд: A.O. Smith Страницы: 24
clage M 3..7-O Operating And Installation Instructions preview
M 3..7-O
Бренд: clage Страницы: 148

Бренды по названию

Популярные бренды

Загрузить еще бренды