ITT HT 3196 i-FRAME Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 148

background image

105

184

106

Remove the frame adapter (MTi, LTi , XLT-i)

The 3198 frame adapter is not interchangeable with the adapter of any other model.
1. Remove the dowel pins (469B) and the bolts (370B).
2. Remove the frame adapter (108).
3. Remove and discard the gasket (360D).

You will install a new gasket during reassembly.

Remove the inboard labyrinth oil seal

Labyrinth oil-seal O-rings are part of the 3196 maintenance kits, and they are sold separately.
1. Determine the fit of your labyrinth oil seal.

Table 10: Labyrinth oil-seal fit

Model

Type of fit

STi

O-ring fit into the bearing-frame adapter (228A)

MTi, LTi , XLT-i

O-ring fit into the frame adapter

2. Remove the O-rings (497H and 497J) and the seal (333A).

497H

497J

333A

108

Power-end disassembly

Disassemble the power end ( STi , MTi )

1. Remove the clamp screws (370C) and back off the jam nuts (423).
2. Tighten the jack screws (370D) evenly to move the bearing housing (134) out of the bearing frame

(228A).

3. Remove the shaft assembly from the bearing frame (228A).

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

73

«
...
73
74
75
76
77
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: A.O. Smith Страницы: 24

Бренд: Gardena Страницы: 13

Бренд: WarmFlow Страницы: 89

Бренд: Danfoss Страницы: 40

Бренд: TapFlo Страницы: 42

Бренд: Barnes Страницы: 20

Standard Series

Бренд: Facilities Resource Group Страницы: 61

Бренд: Jandy Страницы: 16

Бренд: Kärcher Страницы: 18

Aquarea WH-ADC0309J3E5B

Бренд: Panasonic Страницы: 40

Бренд: Calpeda Страницы: 43

PacificHydrostar 2" Gasoline Powered Clear Water...

Бренд: Pacific hydrostar Страницы: 24

Бренд: Cordivari Страницы: 44

Бренд: Tiger Страницы: 36

Бренд: Gorenje Tiki Страницы: 48

Бренд: Nagman Страницы: 15

Бренд: Oase Страницы: 7

Бренд: Pearl Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды