ITT HT 3196 i-FRAME Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 148

background image

134

122

112A

11. Remove the bearing locknut (136), the bearing lockwasher (382), and the outboard bearing (112A).

NOTICE: Use force only on the inner race when you press bearings off the shaft. Do not use force
in situations in which you might break a part. Doing so may result in equipment damage.

NOTICE:
Save the bearings for inspection. Do not reuse the bearings. Doing so may result in decreased
performance.

122

136

112A

382

Disassemble the power end ( XLT-i and i17 with duplex bearings)

1. Remove the bearing frame to frame foot (241) using the frame-foot bolts (370F).

228A

241

370F

370D

423

134

370C

2. Remove the clamp screws (370C) and back off the jam nuts (423).
3. Tighten the jack screws (370D) evenly to move the bearing housing (134) out of the bearing frame

(228A).

4. Remove the shaft assembly from the bearing frame (228A).
5. Remove the jack screws (370D) and the nuts (423).
6. Remove the bearing housing O-ring (496) and the inboard bearing (168A).

Maintenance

80

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
80
81
82
83
84
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Watson Marlow Pumps Страницы: 95

Бренд: Watson Marlow Pumps Страницы: 87

Бренд: Watson Marlow Pumps Страницы: 127

Бренд: ubbink Страницы: 31

Pure Link 1300 Series

Бренд: lancer Страницы: 20

Бренд: Kospel Страницы: 40

Johnson Pump CombiProLine OH3

Бренд: SPX FLOW Страницы: 67

Бренд: B+BTec Страницы: 20

Бренд: T.I.P. Страницы: 136

Бренд: Homa Страницы: 11

Бренд: O'Clair Страницы: 138

Бренд: Waterax Страницы: 6

Бренд: Calorex Страницы: 24

T4BD-018K Series

Бренд: Nordyne Страницы: 4

Wilden A2550V Series

Бренд: PSG Страницы: 16

Бренд: Daikin Страницы: 40

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Бренд: Hoshizaki Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды