manualshive.com logo in svg

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

ITT HT 3196 i-FRAME - надежный и эффективный насос с высокой производительностью. Установите, работайте и поддерживайте его с помощью инструкции по монтажу, эксплуатации и техническому обслуживанию, которую можно бесплатно скачать с manualshive.com. Надежный помощник в вашем производстве.

Поделиться
Скачать
background image

Reference drawing

The manufacturer supplies a reference drawing with the data package. Keep this drawing for future use
when you perform maintenance and seal adjustments. The seal drawing specifies the required flush fluid
and attachment points.

Before you start the pump

Check the seal and all flush piping.

Mechanical seal life

The life of  a mechanical seal depends on the cleanliness of  the pumped fluid. Due to the diversity of
operating conditions, it is not possible to give definite indications as to the life of  a mechanical seal.

Packed stuffing-box maintenance

WARNING:

• Packed stuffing boxes are not allowed in an ATEX-classified environment.
• Never attempt to replace the packing until the driver is properly locked out and the coupling spacer is

removed.

Accepted leakage rate

It is not necessary to shut down or disassemble the pump to inspect the packing operation. During normal
operation, the packing should leak approximately one drop per second.

Adjustment of  gland

Adjust the gland if  the leakage rate is greater than or less than the specified rate.
Evenly adjust each of  the two gland bolts with a one-quarter (1/4) turn until the desired leakage rate is
obtained. Tighten the bolts to decrease the rate. Loosen the bolts to increase the rate.

Tightening of  packing

NOTICE: Never over-tighten packing to the point where less than one drop per second is observed.
Over-tightening can cause excessive wear and power consumption during operation.

If  you cannot tighten the packing to obtain less than the specified leakage rate, then replace the packing.

Disassembly

Disassembly precautions

WARNING:

• This manual clearly identifies accepted methods for disassembling units. These methods must be

adhered to. Trapped liquid can rapidly expand and result in a violent explosion and injury. Never apply
heat to impellers, propellers, or their retaining devices to aid in their removal.

• Make sure that the pump is isolated from the system and that pressure is relieved before you

disassemble the pump, remove plugs, open vent or drain valves, or disconnect the piping.

• Always disconnect and lock out power to the driver before you perform any installation or

maintenance tasks. Failure to disconnect and lock out driver power will result in serious physical
injury.

• Crush hazard. The unit and the components can be heavy. Use proper lifting methods and wear steel-

toed shoes at all times.

• The pump can handle hazardous and toxic fluids. Identify the contents of  the pump and observe

proper decontamination procedures in order to eliminate the possible exposure to any hazardous or
toxic fluids. Wear the proper personal protective equipment. Potential hazards include, but are not
limited to, high temperature, flammable, acidic, caustic, explosive, and other risks. You must handle
and dispose of  pumped fluid in compliance with the applicable environmental regulations.

Maintenance

64

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Zilmet 521 Instructions For Use Manual preview
521
Бренд: Zilmet Страницы: 10
Garantia Elegance Installation Manual preview
Elegance
Бренд: Garantia Страницы: 2
Agilent Technologies TriScroll 620 Series Installation And Operation Manual preview
TriScroll 620 Series
Бренд: Agilent Technologies Страницы: 26
Homa AM***-C Instruction Manual preview
AM***-C
Бренд: Homa Страницы: 72
Mueller Fre-Heater D Series Installation And Operation Manual preview
Fre-Heater D Series
Бренд: Mueller Страницы: 34
GORMAN-RUPP PUMPS JSV3H60-E5 230/1 Installation, Operation, And Maintenance Manual With Parts List preview
JSV3H60-E5 230/1
Бренд: GORMAN-RUPP PUMPS Страницы: 34
Wijas PERFECT 7000 Assembly And Operation Manual preview
PERFECT 7000
Бренд: Wijas Страницы: 12
Kärcher SBP 2200 Manual preview
SBP 2200
Бренд: Kärcher Страницы: 68
Whale Gusher 30 Series Installation & User'S Instructions preview
Gusher 30 Series
Бренд: Whale Страницы: 8
salmson NOEH Installation And Operating Instructions Manual preview
NOEH
Бренд: salmson Страницы: 48
Dirty Hand Tools 101100 Operation Manual preview
101100
Бренд: Dirty Hand Tools Страницы: 20
Wacker Neuson 0009112 Operator'S Manual preview
0009112
Бренд: Wacker Neuson Страницы: 60
salmson LIFTSON L Installation And Starting Instructions preview
LIFTSON L
Бренд: salmson Страницы: 73
Oilon CUBE 10 EasyAce Installation And Commissioning Manual preview
CUBE 10 EasyAce
Бренд: Oilon Страницы: 58
State Water Heaters SUF-130- 300/400/500 Instruction Manual preview
SUF-130- 300/400/500
Бренд: State Water Heaters Страницы: 76
Dynaset HPW1200/100-440 Operating Instructions Manual preview
HPW1200/100-440
Бренд: Dynaset Страницы: 11
YAMADA NDP-50FAN Operation Manual preview
NDP-50FAN
Бренд: YAMADA Страницы: 26
ebm-papst P2E070-AA26-01 Operating Instructions Manual preview
P2E070-AA26-01
Бренд: ebm-papst Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды