ITT HT 3196 i-FRAME Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 148

background image

122

168A

248A

112A

136

382

253B

7. Remove the bolts (371C), the end cover (109A), and the gasket (360C).
8. If necessary, remove the outboard labyrinth oil seal (332A) from the end cover (109A) and remove the

O-rings (497F and 497G).
Labyrinth oil-seal O-rings are part of the 3196 maintenance kits, or they are sold separately.

109A

332A

371C

360C

9. Remove the bearing housing (134) and bearings (112A) from the shaft (122) .

134

122

112A

10. Remove the bearing locknut (136), the bearing lockwasher (382), and the outboard bearing (112A).

NOTICE: Use force only on the inner race when you press bearings off the shaft. Do not use force
in situations in which you might break a part. Doing so may result in equipment damage.

NOTICE:
Save the bearings for inspection. Do not reuse the bearings. Doing so may result in decreased
performance.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

81

«
...
81
82
83
84
85
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Watson Marlow Pumps Страницы: 131

Бренд: Eaton Страницы: 57

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Бренд: Jandy Страницы: 52

Бренд: Walrus Страницы: 12

Omnivore XLSG200 Series

Бренд: Liberty Pumps Страницы: 12

Бренд: Gardenline Страницы: 28

Бренд: Graco Страницы: 20

Бренд: Aqua MAX Страницы: 56

Бренд: Zenit Страницы: 24

Бренд: KAMMAK Страницы: 8

Бренд: Airetool Страницы: 20

Бренд: T.I.P. Страницы: 120

Бренд: Gude Страницы: 40

VRV III RXYQ5-54PY1

Бренд: Daikin Страницы: 398

AQUANOT SPIN 508

Бренд: Zoeller Страницы: 8

Бренд: AL-KO Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды