Invacare HMV Zoom 300 Скачать руководство пользователя страница 97

Страница: 97 / 116

SECTION 12—BATTERIES AND CHARGER

Part No 1122167

Zoom 300 and Zoom 400

Charging the Batteries

WARNING

NEVER attempt to recharge the batteries by attaching cables directly to the

battery terminals or clamps.
DO NOT attempt to recharge the batteries and operate the powered scooter at

the same time.
If the circuit breaker trips repeatedly, IMMEDIATELY unplug charger and contact

Invacare Technical Service Department.

CAUTION

New batteries MUST be fully charged prior to initial use of the powered scooter.
Always charge new batteries before initial use or battery life will be reduced.
As a general rule, you should recharge your batteries nightly to assure the longest

possible life and to minimize required charging time. Plan to recharge them when

you do not anticipate using the powered scooter.

On-Board Battery Charger

NOTE: For this procedure, refer to FIGURE 12.8.

NOTE: The powered scooter is designed with an electrical lockout to prevent it from being driven
while the charger is plugged into an outlet.

1. Plug AC power cord into on-board battery charger port located on the rear bumper.

2. Plug AC power cord into 110-volt wall outlet.

3. Refer to Battery Charger Operation - Charger Indicator Light on Tiller on page 98.

FIGURE 12.8

Charging the Batteries

Charger Port

AC Power Cord

Rear Shroud

NOTE: Charger port on Zoom 300 shown.
Charger port on Zoom 400 is similar.

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды