Invacare HMV Zoom 300 Скачать руководство пользователя страница 54

Страница: 54 / 116

SECTION 8—TILLER

Zoom 300 and Zoom 400

Part No 1122167

Removing/Installing the Tiller Angle Adjustment
Assembly

NOTE: For this procedure, refer to

FIGURE 8.12.

Removing

1. Remove the tiller. Refer to Removing/Installing the Tiller on page 40.

2. Remove the two (2) mounting bolts that secure the tiller angle adjustment assembly to

the front fork. Refer to FIGURE 8.12.

Installing

1. Install the two (2) mounting bolts to secure tiller angle adjustment assembly to the

front fork. Securely tighten (FIGURE 8.12).

2. Install the tiller. Refer to Removing/Installing the Tiller on page 40.

FIGURE 8.12

Removing/Installing the Tiller Angle Adjustment Assembly

Front Fork

Mounting Bolts

Tiller Angle

Adjustment Assembly

NOTE: Zoom 300 shown.
Zoom 400 is the same.

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды