Invacare HMV Zoom 300 Скачать руководство пользователя страница 89

Страница: 89 / 116

SECTION 12—BATTERIES AND CHARGER

Part No 1122167

Zoom 300 and Zoom 400

8. Secure batteries in the battery tray using the battery strap.

9. Reinstall the rear shroud. Refer to Removing/Installing the Rear Shroud on page 44.

10. Reinstall the seat. Refer to Removing/Installing the Seat on page 34.

NOTE: New batteries MUST be fully charged BEFORE using, otherwise the life of the batteries
will be reduced.

FIGURE 12.3

Removing/Installing the Batteries on Zoom 400

Battery Tray

NOTE: Seat and Rear Shroud not shown for clarity.

Battery Tray

Batteries

Installed

Batteries

Removed

Battery Strap

BLACK Battery

Connector

POSITIVE (+) RED

Battery Terminal

NEGATIVE (-) BLACK

Battery Terminal

POSITIVE (+) RED

Battery Terminal

NEGATIVE (-) BLACK

Battery Terminal

DETAIL “C” - BATTERY WIRING HARNESS

Left Battery

Right Battery

BLACK Battery

Connector

Wiring Harness Connectors

DETAIL “B” - BUILT-IN LIFTING STRAPS

Battery

Lifting Straps

Built-in

Lifting Straps

DETAIL “D” - REMOVING/INSTALLING THE BATTERIES

NOTE: NEVER defeat or bypass any fuse. Only replace with a fuse of the same rating.

NOTE: DO NOT remove fuse or mounting hardware from the POSITIVE (+) RED battery
cable/mounting screw.

DETAIL “A” - BATTERY LIFTING STRAPS

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды