Invacare HMV Zoom 300 Скачать руководство пользователя страница 92

Страница: 92 / 116

SECTION 12—BATTERIES AND CHARGER

Zoom 300 and Zoom 400

Part No 1122167

4. Cut the tie-wrap that secure each the battery terminal cap in place.

5. Slide terminal cap(s) UP on the battery cable(s).

6. Disconnect battery cable(s) from battery(ies) terminal(s)/post(s):

A. POSITIVE (+) RED battery cable from the POSITIVE (+) battery terminal/post.

B. NEGATIVE (-) BLACK battery cable from NEGATIVE (-) battery terminal/post.

FIGURE 12.5

Connecting/Disconnecting the Battery Cables on the Zoom 400

Replacing the Charger

Zoom 300

NOTE: For this procedure, refer to FIGURE 12.6 and FIGURE 12.2.

1. Place the powered scooter in a well ventilated area.

CAUTION

Work should be performed in an area without risking damage to carpeting or floor

covering.

2. Turn power off and remove the key from the ignition.

3. Remove the seat. Refer to Removing/Installing the Seat on page 19.

NOTE: Only battery cable and terminal cap shown. Both caps install in the same manner.

NOTE: DO NOT remove fuse or mounting hardware from the POSITIVE (+) RED battery
cable/mounting screw.

BLACK

Battery

Cable

DETAIL “A” - TERMINAL CAPS

TIE-WRAPS

Battery Handle

Battery

Terminal Caps

U1 Battery

Tie-Wraps

POSITIVE (+)

Terminal Cap

Battery

NEGATIVE (-)

Terminal Cap

To BLACK Battery

Connector

RED Battery Cable

POSITIVE (+)

Battery Terminal

with Bracket

NEGATIVE (-)

Battery

Terminal

Locknut

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды