Invacare HMV Zoom 300 Скачать руководство пользователя страница 21

Страница: 21 / 116

SECTION 4—SEAT

Part No 1122167

Zoom 300 and Zoom 400

Adjusting Seat Height

NOTE: For this procedure, refer to FIGURE 4.3.

NOTE: The seat post has three (3) height settings.

1. Remove the seat. Refer to Removing/Installing the Seat on page 19.

2. Remove the mounting screw, locknut,

and two (2) washers securing the seat
post to the frame post.

3. Align one (1) of the three (3) seat post

mounting holes with the frame post
mounting hole to achieve desired seat
height (FIGURE 4.3).

4. Using the mounting screw, locknut,

and two (2) washers, secure the seat
post to the frame post.

5. Install the seat. Refer to Removing/

Installing the Seat on page 19.

FIGURE 4.3

Adjusting Seat Height

Removing/Installing the Seat Pivot

NOTE: For this procedure, refer to FIGURE 4.4.

Removing

1. Remove the seat. Refer to Removing/

Installing the Seat on page 19.

2. Remove the four (4) mounting bolts

and washers that secure the seat pivot
to the seat.

Installing

1. Install the four (4) mounting bolts and

washers to secure the seat pivot to the
seat. Securely tighten.

2. Install the seat. Refer to Removing/

Installing the Seat on page 19.

FIGURE 4.4

Removing/Installing the Seat

Pivot

Seat Post

17” Mounting

Hole

18”

Mounting

Hole

19” Mounting

Hole

Mounting

Bolts

Mounting

Bolts

Washers

Seat Pivot

Seat

Washers

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды