Invacare HMV Zoom 300 Скачать руководство пользователя страница 36

Страница: 36 / 116

SECTION 7—WHEELS AND CASTERS

Zoom 300 and Zoom 400

Part No 1122167

Removing/Installing the Front Wheel

NOTE: For this procedure, refer to FIGURE 7.2.

NOTE: Take note of position and orientation of wheel and mounting hardware before removing.

Removing

1. Turn power off and remove the key from the ignition.

2. Place the front of the powered scooter up on blocks so that the front wheel is off the

ground.

3. Remove the mounting screw, locknut and two (2) spacers that secure the front wheel

to the fork.

4. Remove front wheel from fork.

Installing

WARNING

Front wheel MUST be mounted in the lower mounting holes for both the Zoom 300

and Zoom 400 - otherwise injury may result.

NOTE: Before installing the front wheel, check the fork for bending. If bent, replace the fork. Refer
to Removing/Installing the Fork on page 37.

1. Align front wheel with the lower fork mounting holes.

2. Secure the front wheel to the fork using the mounting screw, locknut and two (2)

spacers.

3. Securely tighten the front wheel mounting hardware.

FIGURE 7.2

Removing/Installing the Front Wheel

Lower Fork

Mounting Hole

Spacer

Locknut

Fork

Mounting Screw

Spacer

Front Wheel

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды