Invacare HMV Zoom 300 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 116

background image

SECTION 12—BATTERIES AND CHARGER

Part No 1122167

85

Zoom 300 and Zoom 400

CAUTION

When connecting the battery cables to the batteries, the battery cables MUST be

connected to the battery terminals/posts as shown in FIGURE 12.2 for Zoom 300

and FIGURE 12.5 for Zoom 400 - otherwise damage to the battery may result.
For proper battery connection, batteries MUST use post style terminals with

mounting holes through the terminal.

NOTE: If there is battery acid in the bottom of the battery tray or on the sides of the battery(ies),
apply baking soda to these areas to neutralize the battery acid. Before reinstalling the existing or
new battery(ies), clean the baking soda from the battery tray or battery(ies) being sure to avoid
contact with skin and eyes. Determine source of contamination. Never install/reinstall a battery
with a cracked or otherwise damaged case.

Recommended Battery Type

WARNING

The warranty and performance specifications contained in this manual are based on

the use of deep cycle gel cell batteries. Invacare strongly recommends their use as

the power source for this unit.

CAUTION

Failure to use the correct battery size and/or voltage may cause damage to the

powered scooter and give unsatisfactory performance.

Zoom 300 powered scooter uses two (2) 12 volt, 12 Amp-hour (12AH) batteries.

Zoom 400 powered scooter uses two (2) 12 volt, 31 Amp-hour (U1) batteries.

NOTE: Recommended battery type is spill proof and requires no maintenance except routine
charging.

NOTE: Charge batteries daily. Do not allow batteries to completely discharge.

NOTE: Invacare recommends that both batteries be replaced if one (1) battery is defective.

FIGURE 12.1

Recommended Battery Type

12 Volt, 12 Amp-Hour

(12 AH) Battery

12 Volt, 31 Amp-Hour

(U1) Battery

DETAIL “A” - BATTERY USED ON

ZOOM 300

DETAIL “B” - BATTERY USED ON ZOOM 400

«
...
83
84
85
86
87
...
»

Содержание HMV Zoom 300





















































































































Отзывы:

Нет отзывов

Похожие инструкции для HMV Zoom 300

Бренд: Honda Страницы: 174

Бренд: Velotric Страницы: 15

Бренд: Razor Страницы: 4

ML-44GDRS-ES-E100

Бренд: MAXTRA Страницы: 17

Бренд: Merits Страницы: 30

EBIKE MOTION X 35

Бренд: 3T Страницы: 24

Zero 8 Authentic Blue

Бренд: Kettler Страницы: 80

Бренд: Ride VOLO Страницы: 16

Бренд: Ride VOLO Страницы: 18

Бренд: Ride1up Страницы: 22

Бренд: Fortress Technologies Страницы: 52

Бренд: TilGreen Страницы: 22

Бренд: TilGreen Страницы: 65

Бренд: Roma Medical Страницы: 20

Tribred Free Rein

Бренд: Trikke Страницы: 36

Бренд: Trikke Страницы: 36

Бренд: SILENCE Страницы: 64

Бренд: Tern Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды