Invacare HMV Zoom 300 Скачать руководство пользователя страница 69

Страница: 69 / 116

SECTION 11—CONTROLLER

Part No 1122167

Zoom 300 and Zoom 400

FIGURE 11.1

Removing/Installing the Controller

Installing

1. Ensure that the power is off and the key is removed from the ignition.

2. Install the controller on the controller tray using three (3) mounting screws and

locknuts. Securely tighten.

3. Connect the following to the controller (Detail “C” of FIGURE 11.1):

• 6-way rear harness connector

• 8-way rear harness connector

• 4-way motor connector

4. On Zoom 400 only:

A. Install the battery charger. Refer to Replacing the Charger on page 92.

B. Assemble the scooter. Refer to Disassembling/Assembling the Zoom 400 on

page 105.

Controller

Mounting

Screws

Controller

Tray

Locknut

Locknuts

Base Frame

DETAIL “A” - ZOOM 300

Mounting

Screws

Locknuts

Controller

Tray

Scooter Frame

6-way Rear Harness

Connector connects HERE

4-way Motor Connector

connects HERE

8-way Rear Harness

Connector connects

HERE

DETAIL “B” - ZOOM 400

DETAIL “C” - LOCATION OF CONNECTORS

Controller

on Zoom

300

Controller on

Zoom 400

8-way Rear Harness

Connector

connects HERE

6-way Rear Harness

Connector

connects HERE

4-way Motor Connector

connects HERE

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды