Invacare HMV Zoom 300 Скачать руководство пользователя страница 33

Страница: 33 / 116

SECTION 6—SHROUDS

Part No 1122167

Zoom 300 and Zoom 400

Removing/Installing the Boot Assembly

NOTE: For this procedure, refer to FIGURE 6.4

NOTE: Reverse this procedure to install the boot assembly.

1. Remove the front shroud. Refer to Removing/Installing the Front Shroud on page 31.

2. Remove the tiller. Refer to Removing/Installing the Tiller on page 40.

3. Remove the front shroud and boot assembly from the scooter.

4. Remove the boot assembly from the front shroud by disengaging the boot from the

tabs on the front shroud.

NOTE: On the Zoom 400, the boot will have to be slipped off the front basket bracket after
disengaging the boot from the tabs. Refer to Detail “A” of FIGURE 6.4.

FIGURE 6.4

Removing/Installing the Boot Assembly

Tab

Boot

Assembly

Front

Shroud

Front Shroud

Boot Assembly

Front Basket

Bracket

NOTE: The Zoom 400 is shown. The Zoom 300 is the same without the front basket bracket.

Front Basket

Bracket

DETAIL “A”

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды