Invacare HMV Zoom 300 Скачать руководство пользователя страница 62

Страница: 62 / 116

SECTION 9—SWINGARMS

Zoom 300 and Zoom 400

Part No 1122167

SECTION 9—SWINGARMS

WARNING

After any adjustments, repair or service and before use, make sure that all attaching

hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power OFF and

remove key from ignition.

Removing/Installing the Swingarms

NOTE: For this procedure, refer to FIGURE 9.1.

Removing

1. Turn power OFF and remove the key from the ignition.

2. Remove the seat. Refer to Removing/Installing the Seat on page 19.

3. Remove the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

4. Remove the batteries. Refer to Removing/Installing the Batteries on Zoom 300 on

page 86 and Removing/Installing the Batteries on Zoom 400 on page 88.

5. Remove the drive wheel. Refer to Removing/Installing the Drive Wheels on page 34.

6. Support the transaxle.

7. Remove the cotter pin on the swingarm.

8. Slide out the two (2) washers, two (2) glide bearings and swingarm assembly.

9. Remove the viscous element from the drive shaft.

10. If necessary, repeat STEPS 5-8 for the other swingarm assembly.

Installing

1. Install the viscous element on the drive shaft.

2. Install the two (2) washers, two (2) bearing glides and swingarm assembly as shown

in FIGURE 9.1.

3. Install the cotter pin on the swingarm.

4. Install the drive wheel. Refer to Removing/Installing the Drive Wheels on page 34.

5. If necessary, repeat STEPS 1-4 for the other swingarm assembly.

6. Install the batteries. Refer to Removing/Installing the Batteries on Zoom 300 on

page 86 and and Removing/Installing the Batteries on Zoom 400 on page 88.

7. Install the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

8. Install the seat. Refer to Removing/Installing the Seat on page 19.

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды