Invacare HMV Zoom 300 Скачать руководство пользователя страница 32

Страница: 32 / 116

SECTION 6—SHROUDS

Zoom 300 and Zoom 400

Part No 1122167

Zoom 400

NOTE: For this procedure, refer to FIGURE 6.3.

NOTE: Reverse this procedure to install the front shroud on the scooter frame.

1. Remove the seat. Refer to Removing/Installing the Seat on page 19.

2. Remove the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

3. Remove the batteries. Refer to Removing/Installing the Batteries on Zoom 400 on

page 88.

4. Disconnect the tiller wiring harness from the rear wiring harness. Refer to

FIGURE 8.14 on page 57.

5. Disengage the boot from the front shroud. Refer to Removing/Installing the Boot

Assembly on page 33.

6. Remove the tiller. Refer to Removing/Installing the Tiller on page 40.

7. Remove the floormat on the front shroud by pulling up and away.

8. Remove the four (4) mounting screws that secure the front shroud to the scooter

frame.

9. Once the tiller is removed, slide the boot off the tiller and front shroud off the scooter.

NOTE: The boot will have to be slipped off the front basket bracket after disengaging the boot from
the tabs.

10.

FIGURE 6.3

Removing/Installing the Front Shroud - Zoom 400

Front Shroud

Mounting Screws

Boot Assembly

NOTE: Floormat, tiller and fork assemblies, and scooter frame are not shown.

Front Basket Bracket

goes through HERE

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды