Invacare HMV Zoom 300 Скачать руководство пользователя страница 80

Страница: 80 / 116

SECTION 11—CONTROLLER

Zoom 300 and Zoom 400

Part No 1122167

Changing to Left-Handed Operation

NOTE: For this procedure, refer to FIGURE 11.8.

NOTE: The default factory is setting is OFF.

NOTE: For more information, refer to Programming the Controller on page 80.

1. Plug in the programmer to the programmer port on the controller.

2. Press the MENU key to access the Options Menu.

3. From the Options Menu, select Pot Reverse menu.

4. Press the VARY key to change the current setting to ON.

NOTE: The default factory is setting is OFF.

5. Press the ENTER key to confirm the value when finished.

6. Unplug the programmer from the programmer port.

Programming the Controller

Plugging in the Programmer

WARNING

Disengage the brake release lever before making any programming changes. The

scooter will drive if the brake release lever is engaged.

NOTE: For this procedure, refer to FIGURE 11.8.

1. Turn power off and remove the key from the ignition.

2. Remove the seat. Refer to Removing/Installing the Seat on page 19.

3. Remove the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

4. Insert the key in the ignition and turn power on.

5. Locate the programmer port on the controller and remove the black protective cap.

6. Plug in the DS100 programmer into the programmer port.

NOTE: After a few seconds, if a fault is indicated on the display, refer to the back of the
programming card (provided with the programmer) for details.

7. Press the MENU key to scroll through all of the menus available with the programmer.

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды