Invacare HMV Zoom 300 Скачать руководство пользователя страница 72

Страница: 72 / 116

SECTION 11—CONTROLLER

Zoom 300 and Zoom 400

Part No 1122167

Zoom 400

NOTE: For this procedure, refer to FIGURE 8.14, FIGURE 11.1, FIGURE 11.3, and
FIGURE 12.2.

1. Turn power OFF and remove the key from the ignition.

2. Disassemble the scooter. Refer to Disassembling/Assembling the Zoom 400 on

page 105.

3. Remove the charger. Refer to Replacing the Charger on page 92.

4. Remove the controller. Refer to Removing/Installing the Controller on page 68.

5. Disconnect the tiller wiring harness from the rear wiring harness. Refer to

FIGURE 8.14.

6. Remove the rear wiring harness. Refer to Removing/Installing Rear Wiring Harness

on page 74.

7. Remove the circuit breaker. Refer to Replacing/Resetting the Circuit Breaker on

page 76.

8. Remove the four (4) mounting bolts, eight (8) washers and four (4) locknuts that secure

the controller tray to the scooter frame.

9. Remove the two (2) screws that mount the left connector to the controller tray

(Detail “A” of FIGURE 11.3).

10. Repeat STEP 9 for the right connector.

11. Remove the locknut that secures the circuitbreaker to the controller tray.

12. Install the left connector using the two (2) screws as shown in Detail “A” of

FIGURE 11.3.

13. Repeat STEP 12 for the right connector.

14. Install the controller. Refer to Removing/Installing the Controller on page 68.

15. Install the charger. Refer to Replacing the Charger on page 92.

16. Install the circuit breaker. Refer to Replacing/Resetting the Circuit Breaker on page 76

17. Install the controller tray on the scooter frame and secure with four (4) mounting bolts,

eight (8) washers and four (4) locknuts. Securely tighten. Refer to FIGURE 11.3.

18. Install the rear wiring harness. Refer to Removing/Installing Rear Wiring Harness on

page 74.

19. Connect the tiller wiring harness to the rear wiring harness. Refer to FIGURE 8.14.

20. Assemble the scooter. Refer to Disassembling/Assembling the Zoom 400 on page 105.

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды