Invacare HMV Zoom 300 Скачать руководство пользователя страница 43

Страница: 43 / 116

SECTION 8—TILLER

Part No 1122167

Zoom 300 and Zoom 400

Adjusting the Tiller Angle

WARNING

Ensure that tiller is properly adjusted before driving the scooter.
After making any tiller angle adjustments and before use, the tiller MUST be

securely locked into position. Otherwise, a fall from the scooter could occur causing

bodily injury and/or damage to the scooter. Gently, push/pull against tiller to ensure

that the tiller is securely engaged into the adjustment plate.

NOTE: For this procedure, refer to FIGURE 8.2.

NOTE: The powered scooter has an adjustable
tiller. The tiller locks into a position that is most
comfortable for you. The tiller also folds down
for transportation and storage.

1. Pull up on the tiller release lever

located under the right tiller handle.

2. Push/pull the tiller to the desired angle

and release the tiller release lever.

3. Gently, push/pull against tiller to

ensure that the tiller is securely
engaged into the locking mechanism.

NOTE: The tiller is locked in position when an
audible "click" is heard.

FIGURE 8.2

Adjusting the Tiller Angle

Replacing Handgrips

NOTE: For this procedure, refer to FIGURE 8.3

1. Cut the hangrip along the tiller handle.

2. Remove the cut handgrip from the tiller

handle.

3. Spray the inside of the new handgrip

with hairspray.

4. Slide the new handgrip onto the tiller

handle.

5. Repeat STEPS 1 and 4 for the other

handgrip.

FIGURE 8.3

Replacing Handgrips

Up to

Unlock

Down to

Lock

Tiller Release Lever

Tiller

Right Tiller

Handle

Handgrip

Tiller Handle

(Under the Handgrip)

Tiller Assembly

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды