Invacare HMV Zoom 300 Скачать руководство пользователя страница 44

Страница: 44 / 116

SECTION 8—TILLER

Zoom 300 and Zoom 400

Part No 1122167

Removing/Installing the Upper Tiller Shroud

NOTE: For this procedure, refer to FIGURE 8.4.

Removing

1. Turn power off and remove the key from the ignition.

2. Remove the seat. Refer to Removing/Installing the Seat on page 19.

3. Remove the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

4. Perform one (1) of the following:

• On Zoom 300 - Disconnect the RED and BLACK controller connector from the RED

and BLACK battery connector. Refer to FIGURE 12.2 on page 87.

• On Zoom 400 - Disconnect the two (2) BLACK battery connectors from the wiring

harness connectors. Refer to FIGURE 12.3 on page 87.

5. Remove the four (4) mounting screws that secure the upper tiller shroud to the lower

tiller shroud.

CAUTION

Carefully rotate the upper tiller shroud backward to avoid damaging the internal

wiring, otherwise scooter will not operate properly.

6. Gently, rotate the upper tiller shroud backward exposing the internal wiring.

7. Remove the RTV sealant coating the connectors to the PC board.

CAUTION

Remove any RTV sealant coating the connector on the PC board before disconnecting

the connector from the PC board. Otherwise, the PC board could be damaged.
DO NOT use a chemical solvent to remove any RTV sealant from connectors as it

may cause damage to the PC Board.

8. Disconnect the following from the PC board (Detail “A” of FIGURE 8.4):

A. Throttle IDC

B. Headlight connector (Zoom 400 only)

C. Tiller harness connector

Installing

1. Connect the following to the PC board (Detail “B” of FIGURE 8.4):

A. Throttle IDC

B. Headlight connector (Zoom 400 only)

C. Tiller harness connector

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды