Invacare HMV Zoom 300 Скачать руководство пользователя страница 66

Страница: 66 / 116

SECTION 10—TRANSAXLE

Zoom 300 and Zoom 400

Part No 1122167

5. On Zoom 400 only - Assemble the scooter. Refer to Disassembling/Assembling the

Zoom 400 on page 105.

6. Install the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

7. Install the seat. Refer to Removing/Installing the Seat on page 19.

FIGURE 10.2

Removing/Installing the Brake Release Lever

Disengaging/Engaging the Brake Release Lever

WARNING

Ensure that the brake-release lever is in the engaged position before driving. There

should be an audible "click" when stopping and starting.

NOTE: For this procedure, refer to FIGURE 10.3.

The brake release lever manually engages and disengages the brake. The brake release
lever is located under the shroud near the left caster assembly.

1. Perform one (1) of the following:

• To Disengage - Pull the brake release lever out in the direction shown in

FIGURE 10.3.

NOTE: When the brake release lever is disengaged (lever pulled out) and the key is removed, the
powered scooter can be pushed. The powered scooter cannot be driven with the brake in the
disengaged (lever pulled out) position.

• To Engage - Push the brake release lever in, in the direction shown in FIGURE 10.3.

DETAIL “A” - BRAKE RELEASE

LEVER INSTALLED

Brake

Release

Lever

Washer

Cotter Pin

Transaxle

Slot on Controller Tray

for Brake Release Lever

Controller

Tray

Lever Mounting

Bracket

Brake Release

Lever

Washer

Cotter Pin

NOTE: Zoom 300 shown. Zoom 400 brake release lever removes/installs the same way.

Rubber

Tip

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды