Invacare HMV Zoom 300 Скачать руководство пользователя страница 59

Страница: 59 / 116

SECTION 8—TILLER

Part No 1122167

Zoom 300 and Zoom 400

FIGURE 8.15

Replacing the Throttle Assembly

Calibrating Throttle Potentiometer

Mechanical Method

NOTE: For this procedure, refer to Detail “A” of FIGURE 8.15

and FIGURE 8.16

NOTE: This procedure should be performed only when one (1) of the following occurs:

•

Scooter does not drive and the Status LED blinks six (6) or seven (7) times.

•

After replacing the throttle assembly and the scooter does not drive (the Status LED blinks
six [6] or seven [7] times).

1. Turn power off and remove the key from the ignition.

2. Disengage the brake release lever. Refer to Disengaging/Engaging the Brake Release

Lever on page 66.

DETAIL “B” - REPLACING THE THROTTLE ASSEMBLY

Lower Tiller

Shroud

Throttle

Bracket

Tiller

Lever

Locknuts

Lower Tiller

Shroud

Tiller Lever

Throttle

Assembly

Throttle

Bracket

TOP View of

Lower Tiller

Shroud

Throttle IDC

Header

Board

BOTTOM View of

Upper Tiller Shroud

Throttle IDC

Throttle

Assembly

DETAIL “A” - DISCONNECT/CONNECT THE THROTTLE IDC

Throttle Potentiometer Assembled

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды