Invacare HMV Zoom 300 Скачать руководство пользователя страница 20

Страница: 20 / 116

SECTION 4—SEAT

Zoom 300 and Zoom 400

Part No 1122167

Removing/Installing the Seat Post

WARNING

Ensure that the seat post mounting screw is properly engaged and locked. Other-

wise, injury and/or damage may result.

NOTE: For this procedure, refer to

FIGURE 4.2.

NOTE: Take note of position and orientation of the seat post and seat post mounting screw before
removing.

Removing

1. Remove the seat. Refer to Removing/Installing the Seat on page 19.

2. Remove the mounting screw, locknut, and two (2) washers securing the seat post to

the frame post, refer to FIGURE 4.2.

3. Lift seat post up and remove from frame post.

Installing

1. Insert the seat post into the frame post and align the frame post mounting hole with

the desired seat post mounting hole, refer to FIGURE 4.2.

2. Using the mounting screw, locknut, and two (2) washers, secure the seat post to the

frame post.

3. Install the seat. Refer to Removing/Installing the Seat on page 19.

FIGURE 4.2

Removing/Installing the Seat Post

Seat Post

Seat Post Mounting Holes

Washer

Locknut

Mounting Screw

Frame Post

Mounting Hole

Frame Post

NOTE: Seat post on Zoom 300
shown. Seat post on Zoom 400
installs the same way.

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды