Invacare HMV Zoom 300 Скачать руководство пользователя страница 103

Страница: 103 / 116

SECTION 13—MAINTENANCE AND TROUBLESHOOTING

Part No 1122167

103

Zoom 300 and Zoom 400

Brake fault.

Drive Inhibited

Check that the park brake release lever is in the
engaged position. The park brake coil or wiring is
faulty. Check the park brake and wiring.

Out of Neutral

at power up.

Drive Inhibited

Throttle is not in neutral position when turning the
key switch on. Return the throttle to neutral, turn
power off and back on again. Throttle may need to be
re-calibrated.

Speed Pot

error.

Drive Inhibited

The throttle or its wiring is faulty. Check wiring.

Motor volts

error.

Drive Inhibited

The motor or its wiring is faulty. Check wiring.

Other internal

errors.

Drive Inhibited

Call Invacare Technical Services Department.

NUMBER OF

FLASHES

FAULT

IMPACT ON

SCOOTER

NOTES

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды