Invacare HMV Zoom 300 Скачать руководство пользователя страница 48

Страница: 48 / 116

SECTION 8—TILLER

Zoom 300 and Zoom 400

Part No 1122167

Removing/Installing the Headlight Mounting Bracket/
Front Tiller Shroud

NOTE: This procedure is for the Zoom 400
only.

NOTE: For this procedure, refer to
FIGURE 8.7.

Removing

1. Remove the headlight. Refer to

Removing/Installing the Headlight on
page 47.

2. Remove the two (2) mounting screws

that secure the headlight mounting
bracket and the front tiller shroud to
the tiller assembly.

3. Remove the headlight mounting

bracket and the front tiller shroud.

FIGURE 8.7

Removing/Installing the

Headlight Mounting Bracket/Front Tiller

Shroud

Installing

1. Position the headlight mounting bracket and the front tiller shroud onto the tiller

assembly.

2. Secure the front tiller shroud and the headlight mounting bracket using the two (2)

mounting screws.

3. Install the headlight. Refer to Removing/Installing the Headlight on page 47.

4. Install the rear shroud. Refer to Removing/Installing the Rear Tiller Shroud on

page 46.

Front Tiller

Shroud

Headlight
Mounting

Bracket

Mounting

Screws

Tiller

Assembly

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды