Invacare HMV Zoom 300 Скачать руководство пользователя страница 51

Страница: 51 / 116

SECTION 8—TILLER

Part No 1122167

Zoom 300 and Zoom 400

Replacing the Headlight Switch

NOTE: This procedure is for the Zoom 400 only.

NOTE: For this procedure, refer to FIGURE 8.10.

NOTE: RTV sealant is required for this prodcedure.

1. Remove the upper tiller shroud. Refer to Removing/Installing the Upper Tiller Shroud

on page 44.

2. Remove the RTV sealant coating the headlight switch connector.

CAUTION

Remove any RTV sealant coating the connector on the PC board before disconnecting

the connector from the PC board. Otherwise, the PC board could be damaged.
DO NOT use a chemical solvent to remove any RTV sealant from connectors as it

may cause damage to the PC Board.

3. Pull the headlight switch connector to disconnect the headlight switch from the PC board.

4. Push the headlight switch with the attaching wires through upper tiller shroud.

(Detail “B” of FIGURE 8.10).

5. Install the new headlight switch into the upper tiller shroud by inserting the wiring

first then the headlight switch.

6. Push the headlight switch into place until the housing is snug against the upper tiller

shroud. Refer to Detail “B” of FIGURE 8.10.

7. Insert the headlight switch connector into PC board. Refer to Detail “B” of FIGURE 8.10.

8. Apply a thin coating of RTV sealant the headlight switch connector and the PC board.

9. Install the upper tiller shroud. Refer to Removing/Installing the Upper Tiller Shroud

on page 44.

FIGURE 8.10

Replacing the Headlight Switch

Headlight Switch should be snug

against Upper Tiller Shroud

Headlight

Switch

Upper Tiller

Shroud

DETAIL “A”

DETAIL “B”

Top View of

Lower Tiller

Shroud

Bottom View of Upper

Tiller Shroud

PC Board

Headlight

Switch

Headlight

Switch

connects

HERE

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды