Invacare HMV Zoom 300 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 116

background image

SECTION 1—GENERAL GUIDELINES

Zoom 300 and Zoom 400

12

Part No 1122167

SECTION 1—GENERAL GUIDELINES

WARNING

SECTION 1 - GENERAL GUIDELINES contains important information for the safe

operation and use of this product.

DO NOT use or service this product or any

available optional equipment without first completely reading and understanding

these instructions and any additional instructional material such as Owner’s

Manuals, Service Manuals or Instruction Sheets supplied with this product or

optional equipment. If you are unable to understand the Warnings, Cautions or

Instructions, contact a healthcare professional, dealer or technical personnel before

attempting to use or service this equipment - otherwise, injury or damage may

occur.

Repair or Service Information

Set-up of the electronic control unit is to be performed only by qualified technicians. The
final adjustments of the controller may affect other activities of the powered scooter.
Damage to the equipment could occur under these circumstances.

DO NOT service or adjust your powered scooter while occupied, unless otherwise noted.

Operation Information

Invacare products are specifically designed and manufactured for use in conjunction with
Invacare accessories. Accessories designed by other manufacturers have not been tested
by Invacare and are not recommended for use with Invacare products.

Performance adjustments should only be made by professionals of the healthcare field or
persons fully conversant with this process and the driver's capabilities. Incorrect settings
could cause injury to the driver, bystanders, damage to the scooter and to surrounding
property.

After the powered scooter has been set-up/adjusted, check to make sure that the powered
scooter performs to the specifications entered during the set-up procedure. If the
powered scooter does not perform to specifications, turn the powered scooter off
immediately and reenter set-up specifications. Repeat this section until the powered
scooter performs to specifications.

Before using the scooter, verify that the motor is plugged into the harness.

DO NOT connect any medical devices such as ventilators, life support machines, etc., to
the battery. This could cause unexpected failure of the device and the powered scooter.

DO NOT attempt to lift the powered scooter by any removable (detachable) parts. Lifting
by means of any removable (detachable) parts of a powered scooter may result in injury
to the user or damage to the powered scooter.

DO NOT attempt to lift the powered scooter by its tiller, seat or shrouds.

«
...
10
11
12
13
14
...
»

Содержание HMV Zoom 300





















































































































Отзывы:

Нет отзывов

Похожие инструкции для HMV Zoom 300

Бренд: Stratasys Страницы: 24

Бренд: Denver Electronics Страницы: 21

Бренд: Hudora Страницы: 12

Бренд: Hover-1 Страницы: 27

Бренд: Wheel Heels Страницы: 40

Бренд: Urban Страницы: 14

Бренд: CITY BOSS Страницы: 28

Freerider Series

Бренд: Mountain Buggy Страницы: 27

Бренд: Shoprider Страницы: 20

Бренд: E-TON Страницы: 177

Бренд: Retrospec Страницы: 4

Бренд: YBIKE Страницы: 15

Бренд: Lambretta Страницы: 17

Бренд: Handicare Страницы: 86

Бренд: Hello Kitty Страницы: 27

Бренд: RAWLINK Страницы: 79

Бренд: TDC Страницы: 20

Boomerbeast Ultimate

Бренд: Daymak Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды