Invacare HMV Zoom 300 Скачать руководство пользователя страница 87

Страница: 87 / 116

SECTION 12—BATTERIES AND CHARGER

Part No 1122167

Zoom 300 and Zoom 400

5. Install two (2) batteries into the battery tray.

6. Connect the wiring harness to the new batteries in the following order (Detail “B” of

FIGURE 12.2):

A. NEGATIVE (-) BLACK battery cable to the NEGATIVE (-) battery terminal/post on

the LEFT battery.

B. POSITIVE (+) RED battery cable to POSITIVE (+) battery terminal/post on the right

battery.

C. WHITE Battery Cable (Jumper) to the POSITIVE (+) battery terminal/post on the

left battery and the NEGATIVE (-) battery terminal/post on the right battery.

7. Connect the RED and BLACK battery connector to the wiring harness assembly.

Tighten securely.

8. Secure batteries in the battery tray using the hook-and-loop battery strap (Detail “A”

of FIGURE 12.2).

9. Reinstall the rear shroud. Refer to Removing/Installing the Rear Shroud on page 44.

10. Reinstall the seat. Refer to Removing/Installing the Seat on page 34.

NOTE: New batteries MUST be fully charged BEFORE using, otherwise the life of the batteries
will be reduced.

11. If necessary, charge the batteries. Refer to Charging the Batteries on page 97.

FIGURE 12.2

Removing/Installing the Batteries on Zoom 300

DETAIL “A” - REMOVING/

INSTALLING THE

BATTERIES

DETAIL “B” - BATTERY

WIRING HARNESS

Battery

Strap

Battery Tray

Batteries

Installed

NOTE: Seat and
Rear Shroud not
shown for clarity.

Battery Tray

Batteries

Removed

RIGHT

BATTERY

LEFT

BATTERY

POSITIVE (+) RED

Battery Cable

50-Amp Fuse

POSITIVE (+) RED

Battery Terminal

NEGATIVE (-) BLACK

Battery Terminal

POSITIVE (+) RED

Battery Terminal

NEGATIVE (-) BLACK

Battery Cable

WHITE Battery

Cable (Jumper)

RED and BLACK

Battery Connector

NEGATIVE (-) BLACK

Battery Terminal

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды