Invacare HMV Zoom 300 Скачать руководство пользователя страница 65

Страница: 65 / 116

SECTION 10—TRANSAXLE

Part No 1122167

Zoom 300 and Zoom 400

7. On Zoom 400 only - Assemble the scooter. Refer to Disassembling/Assembling the

Zoom 400 on page 105.

8. Install the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

9. Install the seat. Refer to Removing/Installing the Seat on page 19.

FIGURE 10.1

Removing/Installing the Transaxle

Removing/Installing the Brake Release Lever

NOTE: For this procedure, refer to FIGURE 10.2.

Removing

1. Remove the seat. Refer to Removing/Installing the Seat on page 19.

2. Remove the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

3. On Zoom 400 only - Disassemble the scooter. Refer to Disassembling/Assembling the

Zoom 400 on page 105.

4. Remove the cotter pin and washer that attach the brake release lever to the lever

mounting bracket on the transaxle.

5. Twist off the rubber tip from the end of the brake release lever.

6. Remove the brake release lever by sliding it out of the controller tray.

Installing

1. Slide the brake release lever through the slot in the controller tray.

2. Slide the brake release lever into the slot on the lever mounting bracket on the

transaxle.

3. Install the rubber tip onto the end of the brake release lever.

4. Install the washer and cotter pin to secure the brake release lever to the transaxle.

Washer

Swingarm

Assembly

Glide

Bearings

Base Frame

Transaxle
Assembly

Viscous Element

Drive

Shaft

Drive Wheel

Cotter Pin

Swingarm and

Caster Assembly

NOTE: Zoom 300 shown. Zoom
400 transaxle removes/installs
the same way.

Viscous

Element

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды