Invacare HMV Zoom 300 Скачать руководство пользователя страница 24

Страница: 24 / 116

SECTION 4—SEAT

Zoom 300 and Zoom 400

Part No 1122167

Removing/Installing the Seat Positioning Strap

WARNING

The seat positioning strap is a positioning belt only. It is not designed for use as a

safety device withstanding high stress loads such as auto or aircraft safety belts. If

signs of wear appear, belt must be replaced immediately.
ALWAYS wear your seat positioning strap.

NOTE: For this procedure, refer to FIGURE 4.7.

1. Remove the two (2) mounting screws and washers that secure the seat positioning

straps to the arm frame.

2. Remove the halves of the seat positioning strap from the arm frame.

3. Reposition the halves of new seat positioning strap underneath arm frame.

4. Reinstall the two (2) mounting screws and washers that secure the seat positioning

straps to the arm frame. Securely tighten.

FIGURE 4.7

Removing/Installing the Seat Positioning Strap

Washer

Mounting Screw

One Half (½) of Seat

Positioning Strap

Washer

Mounting Screw

Arm Frame

One Half (½) of Seat

Positioning Strap

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды