Invacare HMV Zoom 300 Скачать руководство пользователя страница 47

Страница: 47 / 116

SECTION 8—TILLER

Part No 1122167

Zoom 300 and Zoom 400

Removing/Installing the Headlight

NOTE: This procedure is for the Zoom 400 only.

NOTE: For this procedure, refer to FIGURE 8.6.

Removing

1. Remove the rear tiller shroud. Refer to Removing/Installing the Rear Tiller Shroud on

page 46.

2. Disconnect the headlight connector from the PC board connector (Detail “A” of

FIGURE 8.6).

3. Remove the locknut, washer and mounting bolt that secure the headlight to the

headlight mounting bracket (Detail “B” of FIGURE 8.6).

4. Remove the headlight.

Installing

1. Insert the headlight cable and connector through the hole in the upper tiller shroud

(Detail “B” of FIGURE 8.6).

2. Install the headlight on the headlight mounting bracket using the locknut, washer and

mounting bolt. Securely tighten.

3. Plug the headlight connector to the PC board connector (Detail “A” of FIGURE 8.6).

4. Install the rear tiller shroud. Refer to Removing/Installing the Upper Tiller Shroud on

page 44.

FIGURE 8.6

Removing/Installing the Headlight

Headlight

Connector

PC Board

Connector

Headlight

DETAIL “A”

Headlight

Mounting Bracket

Mounting

Bolt

Washer

Locknut

Headlight

DETAIL “B”

Hole in Upper

Tiller Shroud

Headlight Cable

and Connector

Содержание HMV Zoom 300





















































































































Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды

Invacare HMV Zoom 300, Руководство по обслуживанию

Результаты поиска

Содержание HMV Zoom 300

Отзывы:

Похожие инструкции для HMV Zoom 300

Бренды по названию

Популярные бренды