Intel IXP45X Скачать руководство пользователя страница 744

Страница: 744 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors—HSS Coprocessor

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

744

Reference Number: 004US

Every fourth timeslot received by the HSS is discarded, meaning it is not loaded into

the FIFO and is therefore not sent to the NPE Core.

The HSS can transmit all zeros/ones (NPE Core programmable) for the duration of the

unassigned timeslots.

Received unassigned timeslots are not sent to the NPE Core as they are discarded by

the HSS.

Another method of sending a T1 line over an E1 line called frame mapping is illustrated

Figure 179

. This method groups the 24 timeslots together and places unassigned

timeslots towards the end of the frame. The FBit is located at the last bit of the 32

timeslot, the HSS will not treat this timeslot any differently to other timeslots, it is up

the software to detect the FBit. The NPE Core can select which method it desires to use

when implemented in NPE software.

The NPE Core can program the HSS to automatically ignore (lookup table assigned) the

last eight timeslots. Meaning the NPE Core will not receive the contents of the last eight

timeslots. When timeslot 23 is transmitted, the next data from the NPE Core will not be

transmitted until timeslot zero occurs. The HSS will transmit all zeros/ones for the

duration of the empty timeslots (NPE Core programmable).

The NPE Core must program the HSS to indicate which method of T1 mapping is used

(if any).

13.5.4.2

4.096-Mbps Backplane

This backplane is used to transport two E1s or two T1s on a single line which allows a

clock rate of 4.096 MHz. Two complete E1 frames will fill this frame, therefore

unassigned timeslots are not compulsory. When transporting T1 frames, unassigned

timeslots are used for padding the frame due to the shorter length of the T1 frame.

Note:

In timeslot 0, the frame timeslot is not ignored

Figure 178. MVIP, Interleaved Mapping of a T1 Frame to an E1 Frame

Figure 179. MVIP, Frame Mapping a T1 Frame to an E1 Frame

B2450-01

FBit

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Timeslot

Bits

Unused timeslots

2.048

MHz clock

Frame pulse

2 3

4 5

6 7

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды