manualshive.com logo in svg

Intel IXP45X, Руководство разработчика

Поделиться
Скачать
Intel IXP45X Скачать руководство пользователя страница 384

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors—USB 2.0 Host Controller

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

384

Order Number: 306262-004US

WKDC

Wake on Disconnect Enable (WKDSCNNT_E) — Read/Write. Default=0b. Writing this bit 

to a one enables the port to be sensitive to device disconnects as wake-up events. 
This field is zero if Port Power() is zero.
This bit is output from the controller as signal pwrctl_wake_dscnnt_en (host core only) for 

use by an external power control circuit.

WKCN

Wake on Connect Enable (WKCNNT_E) — Read/Write. Default=0b. Writing this bit to a 

one enables the port to be sensitive to device connects as wake-up events. 
This field is zero if Port Power() is zero.
This bit is output from the controller as signal pwrctl_wake_dscnnt_en (host core only) for 

use by an external power control circuit.

PTC[3:0]

Port Test Control — Read/Write. Default = 0000b. Any other value than zero indicates that 

the port is operating in test mode.
Value

Specific Test

0000b

Not enabled

0001b

J_ STATE

0010b

K_STATE

0011b

SEQ_NAK

0100b

Packet

0101b

FORCE_ENABLE

0110b to 1111b (Reserved)
Refer to Chapter 7 of the USB Specification Revision 2.0 for details on each test mode.

PIC[1:0]

Port Indicator Control — Read/Write. Default = Ob. 
Bit Value Meaning
00b

Port indicators are off

01b

Amber

10b

Green

11b

Undefined

Refer to the USB Specification Revision 2.0 for a description on how these bits are to be used.
This field is output from the controller as signals port_ind_ctl_1 & port_ind_ctl_0 for use by 

an external led driving circuit.

PO

Port Owner—Read/Write. Default = 0. This bit unconditionally goes to a 0 when the 

configured bit in the CONFIGFLAG register makes a 0 to 1 transition. This bit unconditionally 

goes to 1 whenever the Configured bit is zero System software uses this field to release 

ownership of the port to a selected host controller (in the event that the attached device is not 

a high-speed device). Software writes a one to this bit when the attached device is not a high-

speed device. A one in this bit means that an internal companion controller owns and controls 

the port.
Port owner handoff is not implemented in this design, therefore this bit will always be 0.

PP

Port Power (PP)—Read/Write 1b1b/0b – RW. Host controller requires port power control 

switches. This bit represents the current setting of the switch (0=off, 1=on). When power is not 

available on a port (i.e. PP equals a 0), the port is non-functional and will not report attaches, 

detaches, etc.
When an over-current condition is detected on a powered port and PPC is a one, the PP bit in 

each affected port may be transitioned by the host controller driver from a one to a zero 

(removing power from the port).
This feature is implemented in the host controller (PPC = 1). 

LS[1:0]

Line Status—Read Only. These bits reflect the current logical levels of the D+ (bit 11) and D- 

(bit 10) signal lines. The encoding of the bits are:
Bits [11:10] Meaning
00b

SE0

10b

J-state

01b

K-state

11b

Undefined

In host mode, the use of line state by the host controller driver is not necessary (unlike EHCI), 

because the port controller state machine and the port routing manage the connection of LS 

and FS.

Table 141.

PORTSCx - Port Status Control[1:8] (Sheet 2 of 4)

Field

Description

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды