Intel IXP45X Скачать руководство пользователя страница 491

Страница: 491 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Order Number: 306262--, Revision: 004US

491

USB 2.0 Host Controller—Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

9.15.2.3

SOF Interrupt

This SOF Interrupt used for device mode is shared as a free-running, 125-us interrupt

for host mode. EHCI does not specify this interrupt but it has been added for

convenience and as a potential software time base. See

Section 9.12.2, “USBSTS” on

page 375

and

Section 9.12.3, “USBINTR” on page 377

9.15.3

Embedded Design Interface

This is an Embedded USB Host Controller as defined by the EHCI specification and thus

does not implement the PCI configuration registers.

9.15.3.1

Frame Adjust Register

Given that the optional PCI configuration registers are not included in this

implementation, there is no corresponding bit level timing adjustments like is provided

by the Frame Adjust register in the PCI configuration registers. Starts of micro-frames

are timed precisely to 125 us using the transceiver clock as a reference clock. For

example, using a 60-MHz transceiver clock for 8-bit physical interfaces and full-speed

serial interfaces or using a 30-MHz transceiver clock for 16-bit physical interfaces.

9.15.4

Miscellaneous Variations from EHCI

9.15.4.1

Programmable Physical Interface Behavior

This design supports multiple Physical interfaces which can operate in differing modes

when the core is configured with software programmable Physical Interface Modes. See

Configuration Constants. Software programmability allows the selection of the Physical

interface part during the board design phase instead of during the chip design phase.

The control bits for selecting the Physical Interface operating mode have been added to

the PORTSCx register providing a capability that is not defined by EHCI.

9.15.4.2

Discovery

9.15.4.2.1

Port Reset

The port connect methods specified by EHCI require setting the port reset bit in the

PORTSCx register for a duration of 10ms. Due to the complexity required to support the

attachment of devices that are not high speed there are counter already present in the

design that can count the 10ms reset pulse to alleviate the requirement of the software

to measure this duration. Therefore, the basic connection is then summarized as the

following:

• [Port Change Interrupt] Port connect change occurs to notify the host controller

driver that a device has attached.

• Software will write a ‘1’ to the reset the device.
• Software will write a ‘0’ to the reset the device after 10 ms.

— This step, which is necessary in a standard EHCI design, may be omitted with

this implementation. Should the EHCI host controller driver attempt to write a

‘0’ to the reset bit while a reset is in progress the write will simple be ignored

and the reset will continue until completion.

• [Port Change Interrupt] Port enable change occurs to notify the host controller that

the device in now operational and at this point the port speed has been

determined.

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды