Intel IXP45X Скачать руководство пользователя страница 721

Страница: 721 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Order Number: 306262-004US

721

Expansion Bus Controller—Intel

IXP45X and Intel

IXP46X Product Line of Network

Processors

12.5.17

EXP_PARITY_STATUS

The OR of InErrorSts and OutErrorSts is generated to form exp_parity_error which is

routed to the Interrupt Controller which can generate interrupts to Intel XScale

processor. In the event of multiple inbound parity errors or multiple outbound parity

errors, there is a race condition between when software performs a write to clear the

EXP_PARITY_STATUS register and setting the InErrorSts/OutErrorSts error bit in

hardware. If the software clears the error bit before another parity error of the same

type (i.e Inbound), the EXP_PARITY_STATUS register will be set again. However if

software clears the error bit on or after another parity error, the EXP_PARITY_STATUS

way to work around this issue is to ensure no other masters are targeting the

Expansion bus controller while software is clearing the EXP_PARITY_STATUS register.

The only way to stop outbound transactions is to have a software mechanism to stop

the originating master from issuing transfers. The easiest mechanism to stop inbound

Table 237.

EX_ADDR Value to Access EXP_LOCK1 Register

AddrWidth

EX_ADDR[3:0] to read/

write

EXP_INBOUND_ADDR

EX_ADDR[19:4] to read/

write

EXP_INBOUND_ADDR

EX_ADDR[24:20] to read/

write

EXP_INBOUND_ADDR

0x8

“11XX”

0x0000

“10000”

0x9

“11XX”

0x0000

“X1000”

0xA

“11XX”

0x0000

“XX100”

0xB

“11XX”

0x0000

“XXX10”

Register Name:

EXP_PARITY_STATUS

Physical Address:

0xC4000120

Reset Hex Value:

0x00000000

Register Description:

Specifies the parity error status.

Access: See below.

ErrorAddr

InErr

rSt

OutE

rro

rSts

Register

EXP_PARITY_STATUS

Bits

Name

Description

Reset

Value

Access

31:2

ErrorAddr

AHB address[31:2] of the parity error. If multiple parity errors occur,

ErrorAddr contains the address of the first parity error. After receiving

a parity error, the ErrorAddr is locked until InErrorSts and OutErrorSts

are both cleared by software.

0x0

InErrorSts

A parity error occurred on an inbound write. This bit will never get set

if the PAR_EN bit is not set on EXP_MST_CONTROL register.

RW1C

OutErrorSts

A parity error occurred on an outbound read. This bit will not get set

unless PAR_EN is set in the EXP_TIMING_CS for which the parity error

has occurred.

RW1C

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды