Intel IXP45X Скачать руководство пользователя страница 700

Страница: 700 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors—Expansion Bus

Controller

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

700

Order Number: 306262-004US

12.4.7

External Expansion Bus Timing Diagram

12.4.7.1

External Arbiter Timing Diagram

The above timing diagram shows the Expansion bus controller requesting the bus in

cycle 0. The external arbiter chooses to grant the Expansion bus controller in cycle 1.

The Expansion bus controller owns the Expansion bus until it deasserts it request in

cycle 4. The Expansion bus controller cannot start a new transfer in cycle 4 or 5 since it

deasserted its request. In cycle 5, the Expansion bus controller asserts request, but

grant is also lost. Since grant was lost in cycle 5, the Expansion bus controller tri-states

the Expansion bus in cycle 6. The arbiter grants the Expansion bus controller in cycle 6

and the Expansion bus controller now owns the bus until it deasserts request in cycle 8.

In cycle 9, the arbiter chose to park the bus on Expansion bus controller, however the

arbiter chose to deassert grant in cycle 10. When bus parking occurs, the Expansion

bus controller cannot start a new transaction until two cycles after its request is

asserted and only if grant remains asserted. If the external arbiter chose to leave grant

asserted to the Expansion bus controller in cycle 10, the Expansion bus controller would

own the bus until it deasserts request again. When Expansion bus controller is parked

on the bus, all shared Expansion bus outputs are driven to the deasserted state.

12.4.8

Configuration Straps

The Expansion bus controller contains configuration registers beyond what is required

for its own configuration. There are several bits of configuration signals provided as

output from the Expansion bus controller to the rest of the IXP45X/IXP46X network

processors. These signals provide the AHB with functions like the software interrupt

capabilities, location of Expansion bus controller in the processor memory map, PCI

Host/Arbiter information, and configuration information on devices connected to the

Expansion Bus.

One of these general-purpose configuration registers is used to capture the value on

the EX_ADDR pins immediately after reset. In the Expansion Bus Interface, 25 address

lines are used to capture this configuration information during reset. When power up is

complete and reset is asserted, the 25 address lines are configured as inputs. When

internal reset is asserted (PLL_LOCK = 0), the configuration registers latch the values

contained on the 25 address lines and the 25 address lines become configured as

outputs. The Expansion Bus address signals have internal pull-up resistors of about

Figure 163. External Arbiter Timing Diagram

B4462-01

EX_ CLK

- 0 -

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

- 9 -

EX_CS_N

EXPANSION BUS

OUTPUTS

EX_ GNT0_ IXPREQ_N

EX_ REQ0_ IXPGNT_N

STATE

- 10 -

ARBITRATE

GNT IXP

ARBITRATE

GNT IXP

- 11 -

GNT M0

M0_ REQUEST_N

M0_ GRANT_N

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды