Intel IXP45X Скачать руководство пользователя страница 310

Страница: 310 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors—USB 1.1 Device

Controller

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

310

Order Number: 306262-004US

Any valid data in the FIFO remains valid and the software must unload it. The end-point

operation continues normally and does not send another STALL condition, even if the

UDCCS7[SST] bit is set.

To allow the software to continue to send the STALL condition on the USB bus, the

UDCCS7[FST] bit must be set again.

The Intel XScale processor writes a 1 to the sent stall bit to clear it.

8.5.9.6

Force Stall (FST)

The Intel XScale processor can set the force stall bit to force the UDC to issue a STALL

handshake to all OUT tokens. STALL handshakes continue to be sent until the Intel

XScale processor clears this bit by sending a Clear Feature command.

The UDCCS7[SST] bit is set when the STALL state is actually entered, but this may be

delayed if the UDC is active when the UDCCS7[FST] bit is set. The UDCCS7[FST] bit is

automatically cleared when the UDCCS7[SST] bit is set.

To ensure that no data is transmitted after the Clear Feature command is sent and the

host resumes IN requests, software must clear the transmit FIFO by setting the

UDCCS7[FTF] bit.

8.5.9.7

Receive FIFO Not Empty (RNE)

The receive FIFO not empty bit indicates that unread data remains in the receive FIFO.

This bit must be polled when the UDCCS7[RPC] bit is set to determine if there is any

data in the FIFO that the Intel XScale processor did not read.

The receive FIFO must continue to be read until this bit clears or data will be lost.

8.5.9.8

Receive Short Packet (RSP)

The UDC uses the receive-short-packet bit to indicate that the received OUT packet in

the active buffer currently being read is a short packet or zero-sized packet. This bit is

updated by the UDC after the last byte is read from the active buffer and reflects the

status of the new active buffer.

If UDCCS7[RSP] is a 1 and UDCCS7[RNE] is a 0, it indicates a zero-length packet. If a

zero-length packet is present, the Intel XScale processor must not read the data

UDCCS7[RSP] is cleared when the next OUT packet is received.

Register Name:

UDCCS7

Hex Offset Address:

0 x C800 B02C

Reset Hex Value:

0 x 00000000

Register

Description:

Universal Serial Bus Device Controller Endpoint 7Control and Status Register

Access: Read/Write

Bits

(Reserved)

RSP

FST

SST

(Rs

vd)

(Rs

vd)

RPC

Resets (Above)

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды