manualshive.com logo in svg

Intel IXP45X, Руководство разработчика

Поделиться
Скачать
Intel IXP45X Скачать руководство пользователя страница 581

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Order Number: 306262-004US

581

Memory Controller—Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

11.0

Memory Controller

This chapter describes the integrated Memory Controller Unit (DDRI MCU) of the Intel

®

 

IXP45X and Intel

®

 IXP46X Product Line of Network Processors. The operating modes, 

initialization, external interfaces, and implementation are detailed in this chapter.

11.1

Overview

The IXP45X/IXP46X network processors integrate a high performance, multi-ported 

Memory Controller to provide a direct interface between the processor and its local 

memory subsystem. The Memory Controller supports:

• 128/256/512-Mbit, 1-Gbit DDRI

 

SDRAM technology support.

• Unbuffered DRAM support only, no registered DRAM support.
• Dedicated port for Intel XScale

®

 Processor to DDRI SDRAM (Supports critical word 

first reads).

• Between 32 Mbytes and 1 Gbytes of 32-bit DDRI SDRAM for low cost solutions.
• Two AHB ports for access from units other than Intel XScale processor (no critical 

word first support).

• All MMR accesses must go through the South AHB port.
• Single-bit error correction, multi-bit detection support (ECC).
• 32-, 40- wide Memory Interfaces (non-ECC and ECC support).

The DDRI SDRAM interface provides a direct connection to a reliable, high bandwidth 

memory subsystem. The DDRI SDRAM interface consists of a 32-bit wide data path to 

support up to 1066 Mbytes/sec. throughput. An 8-bit Error Correction Code (ECC) 

across each 32-bit word improves system reliability. The ECC is stored into the DDRI 

SDRAM array along with the data and is checked when the data is read. If the code is 

incorrect, the MCU corrects the data (if possible) before reaching the initiator of the 

read. User-defined fault correction software is responsible for scrubbing the memory 

array.

The MCU supports two physical banks of DDRI SDRAM in the form of discrete chips.

— The MCU only supports Unbuffered DDRI memory types.

• The MCU supports a 32-bit DDRI

 

SDRAM data interface. 

• The MCU contains transaction queues for each port enabling pipelining of 

transactions to the DDRI SDRAM for maximum performance.

• The MCU provides two chip enables to the memory subsystem. These two chip 

enables service the DDRI SDRAM subsystem (one per bank).

• Performance monitors for page hit / miss and read latency per port.

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды