Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 7

Страница: 7 / 210

Table of Contents

SCS Series Manual —

P/N 15712:L 7/18/16

3.10: Building-Specific Operation and Programming Examples .......................................................................87

3.10.1: Dedicated System Design................................................................................................................88

Preliminary Design Considerations ......................................................................................................88
Installation ............................................................................................................................................90
Programming (AM2020/AFP1010 Example) ......................................................................................90

3.10.2: Non-dedicated System Design.........................................................................................................96

Preliminary Design Considerations ......................................................................................................96
Installation ............................................................................................................................................98
Programming (AM2020/AFP1010 Example) ......................................................................................98

Section 4: Restrictions ......................................................................................................... 105

Section 5: Ratings and Wiring Diagrams............................................................................ 107

5.1: Introduction................................................................................................................................................107
5.2: Air Flow Switches .....................................................................................................................................108
5.3: Dedicated Smoke Control System Wiring Diagrams ................................................................................108

5.3.1: Fans..................................................................................................................................................108
5.3.2: Motorized Dampers .........................................................................................................................113
5.3.3: EP Dampers .....................................................................................................................................119

5.4: Non-dedicated Smoke Control System Wiring Diagrams .........................................................................126

5.4.1: Fans..................................................................................................................................................126
5.4.2: Motorized Dampers ........................................................................................................................132
5.4.3: EP Dampers .....................................................................................................................................141

5.5: HVAC Wiring Diagrams............................................................................................................................150

5.5.1: Fans..................................................................................................................................................150
5.5.2: Motorized Dampers .........................................................................................................................161
5.5.3: EP Dampers .....................................................................................................................................176

Appendix A: AM2020/AFP1010 Control-By-Event ............................................................. 190

A.1: Introduction...............................................................................................................................................190
A.2: Lists and Equations ...................................................................................................................................190

A.2.1: Control-By-Event Programming Constraints .................................................................................190

A.3: Operators...................................................................................................................................................191

OR ......................................................................................................................................................191
AND

...................................................................................................................................................191

A.4: Size Limitations ........................................................................................................................................194
A.5: The Null Control-By-Event ......................................................................................................................196
A.6: Programming Examples............................................................................................................................198

Options ...............................................................................................................................................198
Example # 1 ........................................................................................................................................199

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 7 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: