Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 141

Страница: 141 / 210

SCS Series Manual —

P/N 15712:L 7/18/16

141

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

5.4.3 EP Dampers

Figure 5.32 EP Damper Control, Non-dedicated System - FSCS Switch Group Type 1

Figure 5.32 depicts an EP damper in a non-dedicated system with the capability of

CLOSED

control and verification of the

CLOSED

state,

switch group type 1. In the above configuration, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally open contactor for

the pressure switch power line. When the CON

OFF⁄CL

CM is activated, the normally open contactor is closed. When the contactor closes,

power is supplied to the pressure switch, which cuts the airflow to the damper and closes it. When the CON

OFF⁄CL

CM is deactivated, the

EMS is free to control the damper. The EMS is currently being overridden by the CON

OFF⁄CL

CM.

When power is supplied to the pressure switch, the damper closes. When the damper completely closes, the damper closed limit switch is

CLOSED

, indicating that the damper is in the

CLOSED

position. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the damper closed limit

switch. In this case the VER

OFF⁄CL

MM is activated because the damper is

CLOSED

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

Power Source

Listed

24 VDC

Power Source

SLC Loop

FCM-1

CON

OFF/CL

(activated)

P-

NF1A

-fs-2

.wmf

Power

Return

VER

OFF⁄CL

(deactivated)

N/O

COM

Limit Switch
for closed
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy

Management

System

1a listed
contact

FMM-1

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 141 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: