Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 73

SCS Series Manual —

P/N 15712:L 7/18/16

73

Configuration

The SCS⁄SCE

Switch Group LEDs for HVAC Mode

The three LEDs associated with each SCS⁄SCE toggle switch or contact function according to Table 3.12.



HVAC Trouble Conditions

When an SCS⁄SCE trouble condition exists, the type of trouble can be identified on the SCS⁄SCE modules by a series of one or more LED
flashes (trouble codes) as described in this section.



HVAC Module Trouble

A trouble affecting the entire SCS⁄SCE is called a module trouble condition. A module trouble may occur for any of the following reasons:

•

Communication is lost with the FACP. All amber trouble LEDs will flash rapidly. During this condition, an annunciator communication
fault will be displayed at the control panel. (COMM LOSS)

Example: Trouble with the EIA-485 communication loop or incorrect address selection.

•

Annunciator points 33-64

For AM2020/AFP1010 only: Annunciator points 33 - 64 are not programmed as type ID ACON and an SCE is not
connected or responding to the SCS. All yellow LEDs will flash rapidly. During this condition, an expander trouble will
be displayed at the control panel. During this condition, an expander trouble will be displayed at the control panel.

•

NF2S-3030, NFS-320/NFS2-640 with NCA-2, or NFS2-3030 with NCA-2: Annunciator points 33 - 64 are not programmed to an
unused output point and the SCE-8 is not connected. All yellow LEDs will flash rapidly. (EXPANDER CONFIG)

Table 3.12 HVAC Toggle Switch Group LED Operation)

SWITCH

GROUP TYPE

Green LED

turns ON when...

Yellow LED

turns ON when...

Amber LED

turns ON when...

1

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

2

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see HVAC Trouble Conditions

3

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

4

CON

OFF⁄CL

CM* Deactivates

CON

OFF⁄CL

CM* Activates

see HVAC Trouble Conditions

5

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

6

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see HVAC Trouble Conditions

7

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

8

CON

ON⁄OP

CM* Activates

CON

ON⁄OP

CM* Deactivates

see HVAC Trouble Conditions

9

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

10

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see HVAC Trouble Conditions

11

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

12

CON

ON⁄OP

CM* Activates

CON

OFF⁄CL

CM* Activates

see HVAC Trouble Conditions

13

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

14

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see HVAC Trouble Conditions

15

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see HVAC Trouble Conditions

*When there is a switch group type selected without verification capability (types 4, 8, and 12), the SCS automatically

annunciates the state that the control module for that group is in.

«
...
71
72
73
74
75
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов