manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 175 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 175

SCS Series Manual —

 P/N 15712:L  7/18/16

175

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.66  Motorized Damper Control - HVAC Switch Group Type 15

Figure 5.66 depicts a motorized damper in an HVAC system with the capability of 

OPEN

 and 

CLOSED

 control and verification of the 

OPEN

 and 

CLOSED

 state, switch group type 15. In the above configuration, the CON

ON⁄OP

CM is activated and the CON

OFF⁄CL

CM is deactivated. Under 

normal operation (non-smoke control mode) both control modules would be deactivated, allowing the EMS system to freely control the 
damper. The CON

ON⁄OP

CM controls two contactors: a normally closed contactor for the damper closed power line, and a dual normally 

open/normally closed contactor for the damper open power line. The CON

OFF⁄CL

CM controls two contactors: a normally closed contactor 

for the damper open power line, and a dual normally open/normally closed contactor for the damper close power line. When the 
CON

ON⁄OP

CM is activated, the CON

OFF⁄CL

CM is deactivated and vice versa. When the CON

ON⁄OP

CM is activated, the normally closed con-

tactor is opened (cutting any power supplied by the EMS to the damper closed power line), the normally closed portion of the dual contactor 
is opened (cutting any power supplied by the EMS to the damper open power line), and the normally open portion of the dual contactor is 
closed, thus supplying power to open the damper.

When power is supplied to the damper open power line, the damper opens. When the damper completely opens, the damper open limit 
switch is 

CLOSED

 and the damper closed switch 

OPENS

, indicating that the damper is in the 

OPEN

 position. The VER

ON⁄OP

MM monitors the 

CLOSED

 position of the damper open limit switch and the VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch. In 

this case the VER

ON⁄OP

MM is activated and the VER

OFF⁄CL

MM is deactivated because the damper is 

OPEN

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed 

24 VDC

Power Source

FMM-1

DM

O

-h1

5a

-fs-2

.wmf

SLC Loop

CON

ON/OP

CM

(activated)

VER

OFF/CL

MM

(deactivated)

Limit Switch
for closed 
position

Damper
Closed
Power

AC 

MOTOR

DAMPER

OPEN

FCM-1 

FCM-1

CON

OFF/CL

CM

(deactivated)

1a, 1b listed contactor

1b listed

contactor

Energy 

Management

System

1b listed contactor

1b, 1a

listed

contactor

FMM-1

VER

ON⁄OP

MM

(activated)

N/O

COM

Limit Switch

for open 

position

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов