Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 137

SCS Series Manual —

P/N 15712:L 7/18/16

137

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.28 Motorized Damper Control

Non-dedicated System - FSCS Switch Group Type 6

Figure 5.28 depicts a motorized damper in a non-dedicated system with the capability of

OPEN

control and verification of the

OPEN

and

CLOSED

state, switch group type 6. In the above configuration, the CON

ON⁄OP

CM is activated. The CON

ON⁄OP

CM controls two contacts: a

normally closed contact for the damper closed power line, and a dual normally open/normally closed contact for the damper open power line.
When the CON

ON⁄OP

CM is activated, the normally closed contact is opened (cutting any power supplied by the EMS to the damper closed

power line), the normally closed portion of the dual contactor is opened (cutting any power supplied by the EMS to the damper open power
line), and the normally open portion of the dual contactor is closed, thus supplying power to close the damper. When the CON

ON⁄OP

CM is

deactivated, the EMS is free to control the damper. The EMS is currently being overridden by the CON

ON⁄OP

CM.

When power is supplied to the damper open power line, the damper opens. When the damper completely opens, the damper open limit
switch is

CLOSED

, indicating that the damper is in the

OPEN

position. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the damper closed

limit switch and the VER

ON⁄OP

MM monitors the

CLOSED

position of the damper open limit switch. In this case the VER

OFF⁄CL

MM is deacti-

vated and the VER

ON⁄OP

MM is activated because the damper is

OPEN

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed

24 VDC

Power Source

FMM-1

DM

O

-nf6

a

-fs-2

.wmf

SLC Loop

CON

ON/OP

CM

(activated)

VER

OFF/CL

MM

(deactivated)

Limit Switch
for closed
position

Damper
Closed
Power

AC

MOTOR

DAMPER

OPEN

FCM-1

FMM-1

VER

ON/OP

MM

(activated)

N/O

COM

Limit Switch

for open

position

1b, 1a listed contactor

1b listed

contactor

Energy

Management

System

*If the SLC device does
not match the one in
this figure, refer to the
SLC manual appendix,
which contains wiring
conversion charts for
type V and type H
modules.

«
...
135
136
137
138
139
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов